Results 1 to 8 of 8

Thread: 2451SL-16 - Round thread on connector?

  1. #1
    Senior Member
    Join Date
    May 2015
    Location
    TN, USA
    Posts
    122

    2451SL-16 - Round thread on connector?

    For the life of me I can't upload a photo to this site. Posting a link to a photo of my actual driver in my Google photo album if anyone would like to see what I'm talking about. Instead of the typical push terminals, this has a round connector with a threaded body. There is a large nut holding the connector to an aluminum plate that covers the area where the push terminals would normally be. From the looks of it, I would assume whatever cable connector is used with this would push in and then thread on to lock. Wild guess, but maybe it also has a rubber seal for moisture protection? This was purchased as a NOS part, and didn't come out of any cabinet.https://photos.app.goo.gl/JeX2fdjatRe1azUV6

  2. #2
    Senior Member grumpy's Avatar
    Join Date
    Oct 2003
    Location
    SoCal
    Posts
    5,742
    Looking to change to push connectors? or use as-is and get the connector info?... either way, it looks rather OEM (Special run for outside use?) and JBLPro may be of assistance.

  3. #3
    Senior Member
    Join Date
    Jul 2003
    Location
    Orange County, CA
    Posts
    3,597
    Like I said elsewhere, it looks like a two prong CB mic connector and you need the female.https://vetco.net/products/2-pin-fem...IaAuqYEALw_wcB

  4. #4
    Senior Member
    Join Date
    Aug 2017
    Location
    WDC USA
    Posts
    310
    Possibly a Switchcraft EN3 connector or variation on it .https://www.mouser.com/new/switchcraft/switchcraften3/

  5. #5
    Senior Member
    Join Date
    Feb 2009
    Location
    annapolis, md usa
    Posts
    704
    Quote Originally Posted by emilime75 View Post
    For the life of me I can't upload a photo to this site...
    Post 26 of this thread, follow the instructions. You may have to resize the image down if it still doesn't work but this should fix it.
    https://www.audioheritage.org/vbulle...ad-error/page2

  6. #6
    Senior Member
    Join Date
    Jul 2003
    Location
    Orange County, CA
    Posts
    3,597
    Quote Originally Posted by rusty jefferson View Post
    Post 26 of this thread, follow the instructions. You may have to resize the image down if it still doesn't work but this should fix it.https://www.audioheritage.org/vbulle...ad-error/page2
    OK, post this address in your browser and it should take you to the place that sells them, complete with picture.https://vetco.net/products/2-pin-fem...IaAuqYEALw_wcB

  7. #7
    Senior Member
    Join Date
    May 2015
    Location
    TN, USA
    Posts
    122
    Quote Originally Posted by grumpy View Post
    Looking to change to push connectors? or use as-is and get the connector info?... either way, it looks rather OEM (Special run for outside use?) and JBLPro may be of assistance.
    I'd prefer to find the cable end and use it as is. Tried taking the round connector off and it felt like I was about to damage something, so I stopped.

  8. #8
    Senior Member
    Join Date
    May 2015
    Location
    TN, USA
    Posts
    122
    Quote Originally Posted by toddalin View Post
    OK, post this address in your browser and it should take you to the place that sells them, complete with picture.https://vetco.net/products/2-pin-fem...IaAuqYEALw_wcB
    This does look like it may be it, thanks.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Right Angle IEC Connector
    By JBLOG in forum General Audio Discussion
    Replies: 1
    Last Post: 12-07-2008, 10:53 AM
  2. Are 5235 X-over XLR connector non standard?
    By scorpio in forum Lansing Product DIY Forum
    Replies: 8
    Last Post: 12-07-2007, 01:40 PM
  3. LE 26 connector polarity
    By analog addict in forum Lansing Product Technical Help
    Replies: 2
    Last Post: 10-09-2006, 06:30 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •