Results 1 to 10 of 10

Thread: A toddler and his JBL 4343B battling polarity

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Senior Member
    Join Date
    Sep 2013
    Location
    Flat Earth
    Posts
    181

    A toddler and his JBL 4343B battling polarity

    Imagine for a second that you're teaching a toddler to work out this puzzle box



    Now replace the toddler with me, the box with JBL 4343B and the pieces with wires and polarity but keep the same mindset, we good?

    Ok, so on to the issue here. I own a pair of 4343B with charge coupled network and passive xover between (mid, hf and uhf). The lf driver (2235h) and the rest requires active xover. The rear of the speakers has two sets of terminals, one pair for the lf and one pair for the mid, hf and uhf drivers.

    1) I'm going over the polarity of the system and I hooked up a 9V battery to check the polarity of the woofer. Connecting the speaker terminals to a 9V battery, Red to + and Black to - made the cone go inwards. Since the speakers will be used together with subs where Red to + and Black to - made the cone move outwards I need to make some adjustments.

    2) I did not do a polarity check on the (mid, hf and uhf) wired to the network as I was afraid I might damage something, and I wouldn't know how to see the polarity of the hf and uhf drivers anyways.

    3) Since the speakers require an active crossover they also require four channels.

    4) I assumed it would be as easy as (Amplifier Red to Speaker Black) and (Amplifier Black to Speaker Red) but then I came across this post in the forums http://www.audioheritage.org/vbullet...wfull=1#post30

    Quote Originally Posted by boputnam View Post
    If you are going to reverse the polarity of a JBL cabinet, it must be done AT EACH COMPONENT in the cabinet. You should not simply hook-up the cabinet red-to-black. That will not have the proper effect, because that will result in the signal being pathed through the transducer before the capacitor(s) - this is a DC circuit, and that is backwards. For the crossover network to work properly, the capacitor(s) must see the signal BEFORE the transducer, regardless of cabinet (and transducer) polarity.

    To "correct" or re-phase a vintage JBL cabinet, you need to reverse-wire at each component. Simply alter the signal path AFTER the crossover and before the transducer, at each component binding posts.

    As example, if your cabinet is out-of-phase (negative), and woofer is wired GRN-to-red post, switch the woofer to GRN/BLK-to-red post. Reverse the wiring for EACH component (this will ensure the mid-range stays 180-degrees out-of-phase in 3-way cabinets). The woofer - and cabinet - will then be positive, and industry standard.

    It is handy - but not necessary - to review the network schematics, if you're so inclined, and yours is available:

    Link: http://www.jblproservice.com/pdf/Network%20Schematics/
    A) So now I'm not sure what to do? I can't do as I assumed in point #4?

    B) Should I and how would I go about making the speakers adhere to the current industry standard, please?

    PS: I did read the polarity convention of JBL transducers and systems pdf, but again, refer to the puzzle box, please.

  2. #2
    Senior Member macaroonie's Avatar
    Join Date
    Jan 2005
    Location
    near Glasgow Scotland
    Posts
    2,288
    Be aware that some amplifiers invert the signal. Hence if you are using different amps where one inverts then you have to allow for this also

  3. #3
    Senior Member
    Join Date
    Sep 2013
    Location
    Flat Earth
    Posts
    181
    My life just got harder. I'm using a vintage Denon POA 1500 for mid, hf & uhf and a QSC GX5 for the 2235's.

    How can I check if those amps does that, and if they do, then what can I do to diddelido? ....

    Sorry, I mean, if they invert, does that mean that the poles are switched at the amplifier's binding posts? If yes, then I can check the voltage with a multimeter.

  4. #4
    Senior Member grumpy's Avatar
    Join Date
    Oct 2003
    Location
    SoCal
    Posts
    5,742
    If you have the biamped 4343 working right as a system, just make sure the sub
    is phased appropriately (e.g. if you intentionally overlap the 4343 and sub
    and they're out of phase, you'll get a hole in response that should be easy
    to spot).

  5. #5
    Senior Member
    Join Date
    Sep 2013
    Location
    Flat Earth
    Posts
    181
    Grumpy, yes, that's what I've been doing up until now. I'm using DIY subs and midbass modules and these are managed by miniDSP 4x10. I can invert using that (which is what I have done in the past), but I'd like everything to adhere to present standards. Now everything except the speakers are physically wired so that + from battery to red/(+) on subwoofers & midbass modules (SpeakOn) connectors make the cones move outwards, ie positive polarity.

    For the speakers the cone moves inwards when doing the 9V battery test, ie negative polarity.

    The goal is that the speakers are also wired for positive polarity to have a uniform standard across the system.

    I'm not sure what to do to make that happen.

  6. #6
    Senior Member grumpy's Avatar
    Join Date
    Oct 2003
    Location
    SoCal
    Posts
    5,742
    I'm afraid I don't understand the point of your goal.

    The drivers are operating with -intended- phase/polarity with each other, or they are not.
    This is important to get right. It sounds like you have done this.

    If the slope of the electrical crossover has been changed from the original design,
    the necessary phase/polarity of a particular driver -may- also require a change as
    well as some EQ.

    The system is operating with a positive signal providing positive displacement (out) of the
    bass drivers (not necessarily true for other drivers) with red amp terminals connected
    to red speaker terminals, or it is not.

    I won't argue whether this is important or not.

    If it is important to you, make it so. If the bass driver in the 4343 needs to be flipped
    in polarity to accomplish this, then it is important to flip the rest (vs. the factory wired polarity).

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Please help me identity 4343B
    By martin_wu99 in forum Lansing Product General Information
    Replies: 8
    Last Post: 12-11-2012, 02:16 AM
  2. jbl 4343b
    By sgaggy in forum Lansing Product General Information
    Replies: 11
    Last Post: 03-12-2007, 09:21 PM
  3. 4343B is playing
    By Rolf in forum Lansing Product General Information
    Replies: 9
    Last Post: 07-01-2005, 12:02 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •