View Full Version : Finding parts for old JBL 2482 Comp Driver(s)
pocketchange
05-29-2007, 03:48 PM
Getting the diaphragms isn't a problem but getting something as easy as the diaphragm cap fillister screws is akin to finding a needle in a hay stack.
Anyone have spares? I'm needing 8, if someone can point me in the direction
of a vendor or someone that may have them, I'll buy you a beer...
They have .250 head (#8) phillips 10-32 X 2". I have found some .303 slot but would rather not hack up the diaphragm caps getting them to fit.
JBL parts was a wasted effort, sending common steel 1/4 X20 hex = :blink:,
not even close.
Thank You,
pc
sourceoneaudio
05-29-2007, 04:01 PM
Here you go.
NUTZ and BOLTZ for everything.
http://www.copperstate.com/
Jeff
J/S-S1A :D
pocketchange
05-29-2007, 04:09 PM
www.copperstate.com doesn't have them either :o:.
subwoof
05-29-2007, 09:02 PM
Get some standard pan head bolts of the correct length and find someone with a vertical belt sander and sand down the heads to fit. Wear gloves and get a few extras to practice with.
Be sure to clean out the holes with a bottom tap and light oil before re-assembly.
you will not find them anywhere...and getting someone in JBL parts to figure out the correct number only to find out they are NLA will take up a few hours of your life..)
sub
Steve Schell
05-30-2007, 12:37 AM
Good advice from subwoof on cleaning the holes with a tap. The ferrous junk does tend to stay lodged in the hole due to the driver's magnetic circuit. I have had decent luck cleaning the holes using a nail with a big neo magnet stuck to it.
Earl K
05-30-2007, 05:42 AM
They have .250 head (#8) phillips 10-32 X 2". I have found some .303 slot but would rather not hack up the diaphragm caps getting them to fit.
JBL parts was a wasted effort, sending common steel 1/4 X20 hex = ,
not even close.
Some 1990 era catalogue info ( ie; these parts numbers may not be current or relevant in 2007 ) :
- Ask JBL parts if Catalogue No ; SC-MS52602 means anything to them these days . The part number description says it is a screw for the cover ( Back-Cap ) of the 2440/41 driver ( which is the same as the 2482 ) . The "screw" to hold the diaphragm in place ( for the 2440/1/5 ) would be SC-MS32164 .
- The screw holding the "Back-Cap" of a 2420/1/2470/le85 type driver is part number ; SC-MS52601 .
- They may need to strip out the "SC-" prefix to do a proper database search.
- It appears any prefix before "MS#####" was used as a descriptor for the general class type . ( example 1 ; Cardboard Shipping Boxes or Cartons, begin with: CTN-MS##### ), ( example 2 ; Dust Domes, begin with: DD-MS##### ), ( example 3 ; FoilCals, begin with: FL-MS##### ), ( example 4 ; Screws , begin with: SC-MS##### )
:)
ps : MS##### ; That's the letter "S" after the "M" / ( not the number "5" ) .
mech986
05-30-2007, 08:45 AM
Here's the listing from the current JBL Pro parts list:
52602 SCR, MACH 10-32X2 $ 2 .70 USD EA
The MS designation is for Machine Screw IMO.
Here's the old 2441 pdf describing the screw parts:
http://www.jblproservice.com/pdf/Discrete%20Sales%20Models/2441.pdf
pocketchange
05-30-2007, 09:02 AM
Thank You...
pc :applaud:
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.