How does one separate the diaphragm from the magnet? And having done so, how does one correctly replace it?
How does one separate the diaphragm from the magnet? And having done so, how does one correctly replace it?
Also, on the grill, does anyone know the correct sizing for the o-ring? It looks like 1/16" x 2-7/8 ID.
I don't think it was an O-ring on the original 044s, more like a window screen spline without the splines. I think it came as a single length with open ends. The 035 screen locks are O-rings but none of the 044s I've seen are. Of course the hard part is the color. The JBL parts I have for the 035s are black but are the same length (diameter 3") as the 044 gray "strings". The black 035 O-rings measure about 2mm diameter and the 044 gray strings seem to be a bit thicker, closer to an 1/8". Diameter of the 044 and 035 screens are both about 3" and the gasket doesn't have to stretch, just to force into the groove. The JBL part number for the 035 ring is 62664, if that helps. I haven't tried swapping them but I could if it would help. I've got plenty of spare 044s out of cabinets, and a bag new of 035 O-rings.
What I can't seem to lay my hands on is my tiny caliper. I believe I took it over to a neighbors to measure the seals in his clutch master cylinder on an antique BMW.
Whatever rubber parts were on the mesh of my 044(ti) disintegrated, but the magnet is strong enough to hold them in place with no rubber parts. I stick stick them in the groove and they stay put.
Also a perfectly good approach. The stuff that came out of this one (in small bits) was black, 1/16" in diameter (0.070) and the groove is 2-7/8" (2.864) inner diameter. There are o-rings available with those dimensions in a variety of materials. But any 1/16" o-ring could be cut and used as long as it was long enough.
So how does one separate the diaphragm? I want to push out some small dents but the thing won't come off the magnet.
... assuming you've disassembled the tweeter to the point where there's
a fiber-board carrying the dome (and coil), and leads in view... this has
to be separated from the magnet assembly to see the back side of the
dome (I'm assuming this is the same view as a silver 044). Frankly, I
wouldn't recommend trying this as it can be difficult if the adhesive
is well ... adhered. Others here have tried this and have found it to be
less of an issue. There should be a foam cylinder behind the dome,
likely glued to the magnet assembly, which should be put back in place
(or left alone if still glued).
Good luck, if you decide to forge on.
I haven't gone as deeply as to remove the diaphragm, but some here have said it either comes right off easily or, as Grumpy implies, it's stuck.
But to the O-ring: I have every reason to believe it's the same one as the 035Ti/TiA/052Ti which is JBL Pro part #62664 RETAINER SCREEN. Retail price of a whopping $0.36. Find whatever you want that works but I just had JBL send me a bag of eight, which now happens to be just the number of 035/052 tweeters I now have in use. I can't confirm that part number for the 044Ti since the exploded diagram for the 240Ti doesn't identify that part. The original gray retainer for the 044, part #60752, seems rather indestructible by comparison and is not listed as available.
Slide a thin putty knife or some other such blade GENTLY between the fiber board diaphragm assembly and the magnet top plate. The fiber board has adhesive on it much like clear packing tape. Just lift the phragms gently and the bond will release.
Be super careful how far in you probe with the knife blade as you risk hitting the tiny voice coil.
One step above: "Two Tin Cans and a String!"
Longtime Alaskan Low-Fi Guy - E=MC² ±3db
That's about what I figured was needed, but I don't want to damage the coil. Since the diaphragm is near-junk anyhow, I may just swap in a 044 magnet-phragm assembly anyhow. I can live with it not being gold colored till another 044-1 comes along.
Ah, well, I found out how far you can safely insert a blade without shearing off the voice coil. Oh well, it was a learning experience. It was FUBAR anyhow. Damn thing popped loose and the blade went clean through. This was a good tweet for me to learn on.
Did you know you can see daylight through these diaphragms? There's really not very much metal on them at all.
I'm pretty sure that painting one is not in my future, but thanks for the suggestion. I'll just use an 044 until the right replacement comes along.
The key term was Gently.
There is NOT much aluminum there at all. I still think Krylon!
One step above: "Two Tin Cans and a String!"
Longtime Alaskan Low-Fi Guy - E=MC² ±3db
There are currently 1 users browsing this thread. (0 members and 1 guests)