Results 1 to 10 of 10

Thread: crown ce2000 vs yamaha pc4002m

  1. #1
    Senior Member
    Join Date
    Apr 2005
    Posts
    146

    crown ce2000 vs yamaha pc4002m

    Hello . I am HAVING A HARD TIME FINDING A YAMAH PC 4002 M AMP.I WANT TO RUN ONE OF THESE AMPS TO MY WOOFERS. WHICH ONE WILL HAVE THE DEEPEST BASS CROWN CE2000 VS YAMAHA PC4002M I HAVE JBL 2245H IN A 12 CUBIC FT CAB-WITH 2202H-2425H-2404H

  2. #2
    Senior Member
    Join Date
    Apr 2003
    Location
    Covington, Ohio
    Posts
    785
    Hello
    the Yamaha 4002 was produced in the late 1980's and has long since been discountinued. I remember hearing a PA system that used them and thought they sounded very loose on the low end. But a 400 watt amp on that system was way too small for what it was trying to do. I do know some people like the sound of Yamaha amps in general for home use. In pro use they were said not to hold up over the long haul. The CE2000 is still a current model and is also a 400 watt amp into 8 ohms. Between the two I would go with the Crown. The Crown does have a cooling fan at low volumes that my be an issue.
    400 watts per 18 may be a little on low side for power if you really plan to be rocking out.


    Mike Caldwell

  3. #3
    Senior Member
    Join Date
    Apr 2005
    Posts
    146
    Hey. Is the k-2 amp sound any different than the ce-2000.I already spent to much money on the speakers i built I started off with a receiver. now I have a nakamichi pa-7 .sae 202 and 2 crown dc 300. which i will sell everything but nak . so things are tight I dont want to spend any more money. but I will buy a crown high power amp. than that is it for me. how is the sound in the midrandge and the high end department

  4. #4
    Senior Member
    Join Date
    Apr 2003
    Location
    Covington, Ohio
    Posts
    785
    Hello
    The Crown K2 is well regaurded for a amp to use for low end. The power rating of the K2 at 500 watts per channel at 8 ohms is not really much difference than the CE2000 at 400 watts. the K2 however has a completely differnet type of output stage that works very well with low frequency loads and handeling extremes of impeadance swings from the speaker load. It also has no cooling fan and if you read specs it has a 3000 damping factor. For full range use and mid and highs some people prefer different amps over the K2.

    Mike Caldwell

  5. #5
    Senior Member
    Join Date
    Apr 2005
    Posts
    146
    Thanks for the info mike. what amps are you runnig in your system. and how many watts rms

  6. #6
    Senior Member
    Join Date
    Apr 2003
    Location
    Covington, Ohio
    Posts
    785
    Hello
    My live sound PA system is powered with Crown MA3600vz amps and the QSC PL2 series. In the large configuration the mains are 12,000 watts all tri amped. The monitors are all bi-amped QSC powered and depending on the number of mixes it is about 6000 watts.
    If you want to look to pro type of power amps for your system QSC offers many very good sounding models. Others to look at would be Chevin, Lab Gruppen, Camco/Ashly (the new Ashly power amps are now Camco on the inside)
    My home system amp is a 20 plus year old Hafler DH200 I built from a kit.
    Find a Hafler and use it for mids and highs you won't be disappointed.

    Mike Caldwell

  7. #7
    Senior Member
    Join Date
    Apr 2005
    Posts
    146
    jamm on brother

  8. #8
    Senior Member
    Join Date
    Apr 2003
    Location
    Cincinnati Ohio
    Posts
    819
    I just replaced a CE 1000 with a K-1 for the bottom of my bi-amp system. The CE series is great for the price, but cannot compare to the K's. A big CE issue for me was the fan-I hated the noise!

  9. #9
    Senior Member
    Join Date
    Apr 2003
    Location
    Covington, Ohio
    Posts
    785
    On the CE series of Crown amps. the CE 1000 & 2000 models are for lack of a better word "conventional" design power amps. The CE4000 is what some people refer to as what would be the "K3" it uses the same design concept as the K series but higher power.

    Mike Caldwell

  10. #10
    Senior Member JuniorJBL's Avatar
    Join Date
    Feb 2004
    Location
    Utah
    Posts
    1,723
    I also did not care for the CE1000,2000's. But I as well use 2 K2's for LF and they work very well. I did compare them to my Proceed HPA2's and the HPA's had a tad bit more on the bottom end (not very much) but ran out of gas when you wanted to get with it. So I stuck with the K's for sub duty. Besides the HPA2's are really pretty good for full-range duty anyhow

    JMO
    Always fun learning more.......

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Yamaha manuals and parts
    By duaneage in forum Miscellaneous Gear
    Replies: 8
    Last Post: 03-12-2006, 01:08 PM
  2. Crown VFX-2A
    By 4313B in forum Lansing Product Technical Help
    Replies: 6
    Last Post: 04-23-2003, 06:13 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •