Results 1 to 6 of 6

Thread: 4312/L96 questions...........

  1. #1
    victa1
    Guest

    4312/L96 questions...........

    Hello. Three questions for you people....

    How low does the 4312C impendance curve go? Can a Crown DC-300, circa 1970, drive two pairs in parallel without overheating?

    Is the woofer in the 4312 series the same as the one in the old Century L100?

    Who can refoam a pair of L96 woofers?

    Ok, so it was four questions!

  2. #2
    Senior Member "Duke" Spinner's Avatar
    Join Date
    Jul 2005
    Location
    Upstate New York
    Posts
    144
    well, if it's an Old DC300 .....

    4 ohms will give you 340 wpc

    yea, it may get somewhat hot ...

    whats the duty cycle ..??/

    maybe ...add a 1 ohm power resistor ....Crowns recc'

  3. #3
    victa1
    Guest
    The DC-300 used to drive a paralled pair of Advents real good a while back. Those dipped down a bit in some frequency ranges. I just want to be sure before I buy another pair of 4312s.

  4. #4
    Senior Member GordonW's Avatar
    Join Date
    May 2003
    Location
    Marietta/Moultrie GA USA
    Posts
    1,455
    Be aware, that any of these 4310/4311/4312/L100/L100A cabinets equipped with the 123A woofer, will exhibit an effective FIVE TO SIX OHM impedence, of the cabinet. DCR on these woofers is about 4.5 ohms.

    So, two pairs in parallel, could be between 2.5 and 3 ohms. Unless it's something "bulletproof", I would hesitate to "beat on it" with this load attached. I'd expect, if the Crown DC300 was in TIP TOP shape, that it could deal with it no problem... but if it's original old caps and such, I'd be a bit leery...

    Regards,
    Gordon.

  5. #5
    RIP 2011 Zilch's Avatar
    Join Date
    Jun 2004
    Location
    Berkeley, CA
    Posts
    9,963
    I trust these parallel pairs will be in different rooms?

  6. #6
    Senior Member "Duke" Spinner's Avatar
    Join Date
    Jul 2005
    Location
    Upstate New York
    Posts
    144
    2.5 ohms ....

    if yer gonna spank it ...

    is asking for trouble

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. My First Post (aka: questions, questions...)
    By maxjax in forum Lansing Product DIY Forum
    Replies: 12
    Last Post: 08-15-2008, 10:25 PM
  2. First Impressions and Questions on LE-14Cs
    By toddalin in forum Lansing Product Technical Help
    Replies: 5
    Last Post: 09-06-2005, 10:57 AM
  3. Basic questions about schematics
    By evans224 in forum Lansing Product General Information
    Replies: 12
    Last Post: 05-29-2005, 09:17 AM
  4. Kudos and Project Questions.
    By Uncle Paul in forum Lansing Product DIY Forum
    Replies: 1
    Last Post: 03-23-2005, 12:16 AM
  5. Two Questions
    By JBLROCKS in forum Lansing Product Technical Help
    Replies: 2
    Last Post: 02-13-2005, 09:17 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •