Results 1 to 9 of 9

Thread: Group Delay

  1. #1
    Administrator Robh3606's Avatar
    Join Date
    Apr 2003
    Location
    Rocinante
    Posts
    8,704

    Group Delay

    I have a question for you guys. Since group delay is a phase issue how audible is it?? What are "good" numbers?? Also with a sub and woofer set-up is it advantageous to have the group delay numbers as close as possible at crossover or is this made irrelevant buy the crossover because of the inherrenant phase shift.

    Thanks Rob
    Last edited by Robh3606; 07-27-2003 at 02:38 PM.

  2. #2
    Administrator Robh3606's Avatar
    Join Date
    Apr 2003
    Location
    Rocinante
    Posts
    8,704
    "I suppose you've already read Blauert & Laws?"

    Well no actually I have seen the graph often enough. Thanks for the article I can always get the AES reprint. Thanks for the page from Bass Box.

    Rob

  3. #3
    Tom Loizeaux
    Guest
    Wouldn't have JBL engineers worked on this in designing their crossovers?
    Couldn't you correct any remaining group delay by using an active crossover (when bi-amping a 3-way system) by adjusting the delay of the woofer output?

    Tom

  4. #4
    Senior Member GordonW's Avatar
    Join Date
    May 2003
    Location
    Marietta/Moultrie GA USA
    Posts
    1,457
    Seigfried Linkwitz has continued working with this concept; apparently, he is convinced (if I read him right) that group delay in the bass and midbass, is far more audible, at lower levels than the Blaeurt and Laws study indicated.

    If you want, you can check on lots of Linkwitz's work:

    www.linkwitzlab.com

    Fascinating site, from an extraordinarily bright man...

    Regards,
    Gordon.

  5. #5
    Senior Member Ian Mackenzie's Avatar
    Join Date
    Apr 2003
    Location
    Australia
    Posts
    7,742
    Rob,

    This topic is a bit of a brain teaser, It depends on the frequency and sensitivity of the ear/brain to percieved changes in amplitude.

    The Rane site has some excellent reads on this by Debono.

    I'm inclined to think that its a more difficult problem to tame at lower frequencies as the wave lengths are obviously longer.

    Hence, if the group delay of the crossover is xx milliseconds and you get 20 feet of lag on the high pass, how can one create that sort of displacemet correction in their living room without resorting the electronic delay.

    This is why the asymetric all pass crossovers are popular at frequencies below 150hz, as they have minimal group delay if any.

    At higher frequencies, the problem resembles more of an amplitude bump or peak around the crossover point and can be seen as lopes if one can measure the vertical polar response of the drivers.

    I just try and avoid too much displacement according to the Curves then adjust the crossover values for flat response in the listener positon. ie I dont think 2 ms matters much, 3-5 ms yes maybe.

    hope this helps

    Ian

  6. #6
    Administrator Robh3606's Avatar
    Join Date
    Apr 2003
    Location
    Rocinante
    Posts
    8,704
    Hey Giskard. where did your posts go??

    Hello Ian

    I have been doing some reading on the net about the audibility of phase diferences. I have found a couple of good studies but they don't agree on the numbers ie miliseconds of delay. Some say it is more audible some not. I was concerned about what is going on with my 300Hz 24db L/R and my 60Hz 24 Db L/R crossover points. As you say with 360 of phase change that is some delay! And without a digital crossover to correct you have a significant and rather drastic change at crosover phase wise. If you look at Dr Linkwitzs site he now feels that the effects of the high order crossovers are not audible which seems to be a reversal of his previous work. Or should I say not as audible. Lots of contradictions if you look at the references. Well I certainly don't have a good grasp yet but I figure just keep looking and asking questions. I will take a look at the Rane site you mention. It gets a little crazy with combining an all pass crossover function with the L/R filters??? I just have to read up and get a better understanding of the different filter functions as the light is still off

    Rob

  7. #7
    Senior Member
    Join Date
    Apr 2003
    Location
    GTA, Ont.
    Posts
    4,947

    Electronic vs Reflex Tuning induced Group Delay

    Hi RobH
    I actually thought you began this thread to inquire about the audibility of acoustic group delay ( specifically in bass frequencies ) - induced as a consequence of adding a helmholtz resonator into a speaker enclosure. My assumption was based on you mentioning subwoofers and bass - my mistake .

    I did have thoughts about that first premise - though somewhat long winded and not germaine to bessel / butterworth / LR / linear phase / electrical discussions .

    regards <> Earl K
    Last edited by Earl K; 07-28-2003 at 09:48 AM.

  8. #8
    Administrator Robh3606's Avatar
    Join Date
    Apr 2003
    Location
    Rocinante
    Posts
    8,704
    Hello Earl

    "I actually thought you began this thread to inquire about the audibility of acoustic group delay ( specifically in bass frequencies ) - induced as a consequence of adding a helmotz resonator into a speaker enclosure. My assumption was based on you mentioning subwoofers and bass - my mistake ."

    No you are correct but its a 2 parter. I was curious how audible it was and what good numbers are and even if you did match or have the group delay of 2 different driver/enclosure combinations reasonably close or matched would not the phase shift in the crossover throw it out the window. Especially down low between a subwoofer and a woofer where the delays are in 10 of milliseconds. Say at 50 hz 24db 4 order 360 degree delay 20 milliseconds. A little knowledge is dangerous if I am way off track someone smack me please.

    "though somewhat long winded"

    I am all ears!

    Rob
    Last edited by Robh3606; 07-28-2003 at 09:28 AM.

  9. #9
    Senior Seņor boputnam's Avatar
    Join Date
    Apr 2003
    Location
    northern california
    Posts
    7,010
    "...Giskard. where did your posts go??"

    Dang them moderators! They have almost Orwellian powers - can rewrite the past!!

    Giskard has done that occasionally - sometimes he's refining the thought, other times scampering from copyright infringement...

    I've learned to "get 'em while they're hot". But, alas, I had my arms into way too many cabinets this weekend, and was going to give this Thread a good read during the work week .

    Those graphs were pretty helpful. Dang it!

    More on the topic here: http://www.trueaudio.com/post_010.htm, and a proper reference to Blauert and Law's article. If anybody has a "authorized" copy , please pm me...
    bo

    "Indeed, not!!"

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Jbl Sub1500 15" Subwoofer 4 Ohm
    By pangea in forum Lansing Product General Information
    Replies: 519
    Last Post: 05-21-2017, 08:03 AM
  2. Group Delayed Speakers, anyone?
    By MJC in forum General Audio Discussion
    Replies: 36
    Last Post: 10-30-2010, 12:32 PM
  3. Subwoofer Project with JBL 2226
    By 10 Watt Street in forum Lansing Product General Information
    Replies: 13
    Last Post: 12-08-2009, 02:48 PM
  4. time delay problem JBL 4343 (3143 network)
    By B&KMan in forum Lansing Product Technical Help
    Replies: 30
    Last Post: 03-20-2007, 10:09 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •