Results 1 to 8 of 8

Thread: MY BX_6_3A Mock up

  1. #1
    Senior Member LE15-Thumper's Avatar
    Join Date
    Feb 2004
    Location
    Winnipeg, Canada
    Posts
    602

    MY BX_6_3A Mock up

    I used a perf board with pretty good results. I am waiting for the 200k pots to come in to finish it. I tacked a couple of test pots in try it out and it worked perfect ! I used some Wima's and some 1% resistors. Digi-key had all the odd values in stock. I put the TL084 in a socket for ease of replacement.
    Instead of running two output jacks I ran one with a Phase toggle switch. I didn't go to the trouble to complete the pre-outs as this application doesn't require it. It's not as pretty as a PCB design but I am fighting the clock on this project. I found the center of boost to be at 26hz. I am not sure if this is true to orig spec, but both my Sine generator and Sencore scope told me the same frequency. The variable crossover pot worked as expected. You have to wire this dual pot with the two resistive elements tied together at the "TOP" of their wipe to get clockwise-freq increase taper effect. I used 3 pin 7815 / 7915 regulators instead of zeners. The PS board is in the lid. The case is an old Blonder Tongue Mast Amplifier that I gutted. Worked pretty good.
    Any other questions/ critiques are welcome.
    Attached Images Attached Images  
    LE15-Thumper
    "Give me JBL, or give me death"

  2. #2
    Obsolete
    Join Date
    Apr 2003
    Location
    NLA
    Posts
    12,193
    Excellent!

    "I found the center of boost to be at 26hz."

    You're good to go!

  3. #3
    pelly3s
    Guest
    looks really good i wish i had time to build things

  4. #4
    RIP 2011 Zilch's Avatar
    Join Date
    Jun 2004
    Location
    Berkeley, CA
    Posts
    9,963
    COOL! Now we're cookin' here!

    How 'bout a little parts list spreadsheet with sources and costs for those others who might wanna build one?

    Always good to know the bottom line. I'm guessin' $30, no?

    It's just silly to pay big bucks for one....

  5. #5
    Senior Member LE15-Thumper's Avatar
    Join Date
    Feb 2004
    Location
    Winnipeg, Canada
    Posts
    602
    Quote Originally Posted by pelly3s
    looks really good i wish i had time to build things
    Ask Giskard when I first proposed a possible kit to members .....Only took me about 6 months to actually get to it !!!
    LE15-Thumper
    "Give me JBL, or give me death"

  6. #6
    Senior Member LE15-Thumper's Avatar
    Join Date
    Feb 2004
    Location
    Winnipeg, Canada
    Posts
    602
    Quote Originally Posted by Zilch
    COOL! Now we're cookin' here!

    How 'bout a little parts list spreadsheet with sources and costs for those others who might wanna build one?

    Always good to know the bottom line. I'm guessin' $30, no?

    It's just silly to pay big bucks for one....
    Actually, the most expensive item is a nice fancy box to put it into

    You can tell I spared no expense !

    TL084 Op-amp (only one needed) is under a buck. I have the Digi-key part numbers for the odd ball resistor values. I used 1/4 Yageo types. Walll Pack trans need to be 11 to 16v AC ! Not a typical DC type.
    Yeah, net cost well under $50.00 even with fancy jacks and Silver/Teflon wire as shown. I don't have schematic drawing software for the updated power supply. I am sure someone else on the forum knows how to draw it up. It's pretty basic.
    LE15-Thumper
    "Give me JBL, or give me death"

  7. #7
    pelly3s
    Guest
    it took me 6 months to put a switch in a Wah pedal for my cousin, and its taken over a year for me to recone my 2235s. I never have time, although I might take the time to start to make things. I need something to take my mind off of things

  8. #8
    Senior Member Don Mascali's Avatar
    Join Date
    Sep 2004
    Location
    Sarasota, Florida
    Posts
    494
    Nice work.
    4406, 4412A, L100, L100t3 (3 pair), L1, L7, 4645C, 4660A, 4695B, SR4735 and various DIY JBL Pro loaded systems.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •