Results 1 to 15 of 17

Thread: Diy 4315

Hybrid View

  1. #1
    Senior Member bldozier's Avatar
    Join Date
    Jun 2014
    Location
    mount kisco
    Posts
    825

    Diy 4315

    Kits arrived from Vista, found a cabinet maker
    from US Audio Mart.

    Im pleased. The 2105 cut out at 4 3/8 seems
    spacy, buts itís the same on the L88 plus

    i will assemble soon
    Name:  AE7CBDD7-07AB-4547-A276-3234581EAE94.jpg
Views: 423
Size:  65.7 KB

  2. #2
    Senior Member bldozier's Avatar
    Join Date
    Jun 2014
    Location
    mount kisco
    Posts
    825
    The L100t sub enclosure for the le5 is to
    large in diameter for the 4315s, I had ro
    remove the sub-enclosure from the l88 plus
    which fit perfect, the l88 plus can also
    utilize the larger L100t enclosure.

    The carpenter cut the rear cut out for the
    terminal plates to large for the original
    3114 plates, so Iím using 1/2 B.B.
    Attached Images Attached Images  

  3. #3
    Senior Member bldozier's Avatar
    Join Date
    Jun 2014
    Location
    mount kisco
    Posts
    825

    Poor cabinets

    So far every joint is gaping, the bottom and tops are
    not flush with the sides I would not
    be able to veneer them w/o sending out
    to a professional shop first to flush everything up

    i paid $800.00, $500.00 for the cabinets & $300.00
    flat packed from Cali,

    im asking for the seller cut all panels again
    and ship on his dime, or return $600.00

    X#2 on the 4315 cabinets
    Attached Images Attached Images  

  4. #4
    Senior Member bldozier's Avatar
    Join Date
    Jun 2014
    Location
    mount kisco
    Posts
    825
    Name:  A84F15A7-3C9D-47EB-97F3-0640E1009FC6.jpg
Views: 359
Size:  52.7 KBName:  F36E9609-92FC-4F99-B9BC-3D8C829F54BC.jpg
Views: 358
Size:  58.7 KB
    Name:  9972D33E-E2B8-4AC3-A74F-5636AFA25785.jpg
Views: 363
Size:  71.1 KB

    i honestly feel the guy whom made these
    did not test fit the cabinets, Iím not sure
    how these got delivered in this condition

    when end I asked for a test fit the response was
    the joints were to tight and would not separate
    bur was assured fit was perfect,

    the carpenter had these in his shop for 5 months
    my last day to file a claim on them is the 31st of October

  5. #5
    Senior Member macaroonie's Avatar
    Join Date
    Jan 2005
    Location
    near Glasgow Scotland
    Posts
    2,033
    That's a piss poor job. I'm amazed that you couldn't find a wood fabricator locally , that would have been better.

    Can I make a suggestion , get yourself one of these

    Name:  T1964-4.jpg
Views: 363
Size:  115.3 KB

    and offer it up against the corners that should be 90 degrees. You will be able to take pics of that that will confirm your case.

    Also if you measure diagonally both ways across a suspect panel if it is square both measurements will be the same. If it is skewed the measurements will be noticeably different.

  6. #6
    Senior Member bldozier's Avatar
    Join Date
    Jun 2014
    Location
    mount kisco
    Posts
    825
    Name:  3890DF7E-E7F6-496E-9D4A-B308DF3AB80E.jpg
Views: 355
Size:  90.8 KB
    Name:  74E42FA4-7595-4997-9C82-538AE462744A.jpg
Views: 349
Size:  52.7 KBName:  D552EF5B-623B-482E-B977-42EC98CF87BF.jpg
Views: 354
Size:  65.9 KB


    the baffles are fine, all other panels on these cabinets
    are problematic, I asked for the panels to be resawn
    tested and shipped to me,

    the next offer i fer I had was one from Canada
    $750.00 no veneer plus whatever shipping is from
    there,

    $1000.00 from a Lansing member, plus the shipping
    charge. I’m over $1000.00 already on two failed attempts
    on cabinets

    honestly I’m just not quite sure how these were mailed
    to me after 5 months of construction

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 4315
    By push pull in forum Lansing Product General Information
    Replies: 6
    Last Post: 12-12-2008, 01:15 PM
  2. Help with 4315
    By Akira in forum Lansing Product Technical Help
    Replies: 22
    Last Post: 06-28-2008, 04:46 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •