Results 1 to 2 of 2

Thread: BX63. Finally

  1. #1
    Junior Member
    Join Date
    Mar 2017

    BX63. Finally

    After copious research and searching, I finally scored a BX63 without giving up my right arm. I have been using a new manufacture Ashly 1001 crossover with decent results but as many of you know, it's not sloped per JBL specifications and lacks the 6db hump at 26hz. Wow, what a difference. I also moved my B380 from between and to the left of my mains to the left wall of my space slightly rear of center. That move was made with the Ashly crossover still in-line and there was an improvement felt. Adding the BX63 feels like a larger improvement. I also really like the bypass switch. I am running the B380 with a pair of L220's and sometimes it's nice to hear those boys full range. Following JBL's phasing instructions proved more difficult than it initially seemed. One is supposed to place the crossover in bypass, select some program material with a solid base line and slowly increase the BX63 level while putting the unit in and out of bypass until base levels are uniform with the unit in bypass and out of bypass. Then switch phasing and see if the bass gets louder or softer, louder being in correct phase. I have the ability to turn off my mains via a Bryston switch box (also a nice new addition) because I for some reason love A-Bing my speakers... and even with the mains off, I have a hard time hearing the difference when switching from normal and inverted phasing. How subtle is the difference? Everything sounds great but I thought the phasing change would be more obvious. Should I worry? Or just leave it be.

  2. #2
    Senior Member
    Join Date
    Feb 2009
    annapolis, md usa
    Glad you found one and hope it's working properly, but based on my experience with several BX-63As, it may not be. The ones I own or friends own have all developed the same problem, failing power supply capacitors. The symptom is pretty easy to identify.

    Turn on your preamplifier and set the volume to a moderate volume level. Turn on the BX-63(A) and turn the volume all the way down. Turn on your sub amplifier. Leave your full range amplifier off. Start the track with good steady bass. I use which has a steady drum kick and electric bass line. Slowly but steadily increase the volume on the BX-63(A). It should be very linear just like turning up the volume on anything else. If you start to hear music, but then hit a dead spot in sub volume even though you're continuing to increase volume, then suddenly get a big jump in sub volume, you've got the problem. If the volume is even and constant from low to very high, yours is still working properly.

    The description in the manual for set up, is for using the crossover as intended. That is, for controlling the passive high pass filter on your full range speakers as well as the active low pass for the sub(s). The idea is that you wouldn't necessarily hear any difference between your full range speakers (network out) and your full range speakers high passed (network in) with the sub doing the lowest frequencies with normal music/listening. But, when the source goes deeper than than your full range speakers can on their own (pipe organ, synthesizer, cannon, tympani, etc.) the sub will seamlessly fill in the bottom and take the load off the full range drivers, thereby reducing distortion. Not exaggerated bass, but deeper, and with less effort from the full range speakers.

    To find the correct polarity more quickly (assuming the crossover is working properly), use a music track like the one mentioned above at a moderate/high level. Adjust the BX-63(A) so the bass is a little too loud/bloated. Turn off the amps without altering the volume, change the output on the crossover and try again. You should be able to notice the difference now between having less bass or about the same/more bass. The louder of the 2 is the correct polarity. Adjust the bass accordingly. Good luck.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. BX63 or something else
    By 58crewchief in forum Electronic Crossovers
    Replies: 6
    Last Post: 09-04-2017, 10:13 AM
  2. BX63
    By nibbe in forum Lansing Product General Information
    Replies: 9
    Last Post: 12-28-2011, 11:21 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts