I have been working on porting the BSS M2 settings to the Behringer DCX2496.
It was not an easy task because of the implementations differences and the lack of a few EQ and filters types (especially 36dB/oct filters, which is the reason for the difference in the woofer delay setting).
Here are the settings, using 100% of the available power of the DCX2496.
You might have to install a recent version of the firmware (1.16 or 1.17 depending on your hardware version) if you are not able to set all the EQ points.
Even with the last version of the firmware you might have ressource warnings when unsetting an EQ point, but it should work OK
The last two channels are unused, and no EQ of filter point is left for them (make sur you remove any EQ you might have enable there).
They can be used to redirect the left/right input or their sum to a subwoofer, etc...
Input gain (-2.3dB) is set to avoid any risk of UHF saturation when the processor is used at 0dBFS, but this is quite unlikely at these frequencies...Code:Setup: OUT CONFIGURATION LL MM HH OUT STEREO-LINK: ON IN STEREO-LINK: A+B --- Inputs (linked A & B) : GAIN: -2.3dB DELAY: OFF EQ: ON 1: BP 1.14kHz +1.2dB Q=10 2: BP 1.57kHz -1.3dB Q=3.2 3: BP 9.26kHz +2.7dB Q=8.9 4: BP 9.87kHz +1.2dB Q=1.3 5: BP 11.2kHz +2.7dB Q=10 6: BP 13.0kHz +1.1dB Q=4.0 7: BP 15.8kHz +2.9dB Q=5.0 DYN-EQ: OFF --- LF outputs (linked 1 & 2) : INPUT SOURCE: A for output 1 / B for output 2 OUTPUT GAIN: -1.7dB X-OVER ADJUST MODE: FREE high-pass: OFF low-pass: LR48 917Hz EQ: ON 1: BP 22Hz (first "22" step) +3.1dB Q=2.5 2: BP 62Hz -0.9dB Q=4.0 3: BP 92Hz +1.1dB Q=1.1 4: BP 254Hz +2.8dB Q=10 5: BP 196Hz +1.0dB Q=6.3 6: BP 384Hz -9.4dB Q=0.4 (second "0.4" step) 7: BP 393Hz -0.4dB Q=8.9 8: BP 499Hz +1.5dB Q=5.0 9: BP 1.00kHz -7.0dB Q=1.8 DYN-EQ: OFF LIMITER: OFF POLARITY: normal PHASE: 0° DELAY: ON, SHORT=64mm/0.19ms --- HF outputs (linked 3 & 4) : INPUT SOURCE: A for output 3 / B for output 4 OUTPUT GAIN: 0dB X-OVER ADJUST MODE: FREE high-pass: BUT6 1.35kHz low-pass: OFF EQ: ON 1: BP 499Hz +1.1dB Q=5.0 2: BP 770Hz -5.9dB Q=2.8 3: BP 917Hz +3.3dB Q=4.0 4: BP 2.40kHz +0.5dB Q=3.2 5: BP 2.56kHz -1.1dB Q=10 6: BP 2.98kHz -1.4dB Q=10 7: BP 3.24kHz -8.5dB Q=1.4 8: BP 5.54kHz -1.0dB Q=2.5 DYN-EQ: OFF LIMITER: OFF POLARITY: normal PHASE: 0° DELAY: OFF --- Unused outputs (linked 5 & 6) : everything OFF
As with the original BSS settings you might want to rework or remove the high Q woofer EQs at 196Hz and 254Hz if you are not using the original M2 enclosure or an exact clone of them.
Here is a comparison between the measured output of the DCX2496 (red) and the BSS (green) :
Reply With Quote