Page 1 of 4 123 ... LastLast
Results 1 to 15 of 47

Thread: 2203 Subs

  1. #1
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503

    2203 Subs

    I found 2 NOS 2203 recone kits. As I know I can put them into K120, E120, 2202, 2204, 124 and of course 2203 baskets. I'll look for them. Are there any other baskets that fit?

    I want to use them in Subs together with my 4313B DIYs. What do you think?

    Regarding the dimensioning of the subs I found two interesting posts from Giskard:

    1)
    The 2204 can be reconed as a 124/2203 but i'm not sure about the 2206. The 124/2203 works great in a 2.5 - 3.0 cubic foot enclosure tuned to 30 - 32 Hz. In a 2.0 cubic foot enclosure tune to 26 Hz or 40 Hz and see which you prefer. The old JBL tuning frequency for this transducer was 26 Hz but in practice that was usually way too low. The Qts is extremely low at 0.14 (which hints at it's extremely powerful motor).

    The old JBL enclosure chart had the following two recommendations for the 124/2203:

    1.6 to 2.0 cubic feet with a 3" (7 sq in) port having a 8" duct
    2.1 to 3.0 cubic feet with a 3" (7 sq in) port having a 5" duct

    In both cases the Fb was ~ 32 Hz which wasn't in agreement with the user's guide which was, as previously stated, 26 Hz.

    2)
    I've built a significant number of 124/2203-based subs and the best combo I have found is 2.8 cubic feet tuned to 30 Hz.


    Is there a need for active Bass EQ as lot of the subbass modules provide?

    Any recomendations for using them together in on cabinet?

    Any help is appreciated. Thanks!


  2. #2
    Obsolete
    Join Date
    Apr 2003
    Location
    NLA
    Posts
    12,193
    "I want to use them in Subs together with my 4313B DIYs. What do you think?"

    Been there, done that, good idea.
    2.8 cubic feet tuned to 30 Hz.

    "Is there a need for active Bass EQ as lot of the subbass modules provide?"

    Absolutely not. The response is rock solid down to ~ 30 Hz. A high pass filter set in the 20 to 30 Hz range will protect the transducer below resonance thereby increasing mechanical power handling.

    "Any recomendations for using them together in on cabinet?"

    I would keep them in separate sub enclosures within the main enclosure with their centerlines as close together as possible and probably angle them out like many center channel loudspeakers are arranged. Running them that way in parallel will increase their maximum SPL by ~ 6 dB.

    "I found 2 NOS 2203 recone kits. As I know I can put them into K120, E120, 2202, 2204, 124 and of course 2203 baskets. I'll look for them. Are there any other baskets that fit?"

    I'd personally use 2202H or 2204H baskets. Long ago, in another time, it was easy to get 124H's and 2203H's but then the gravy train dried up. Back in the late 80's JBL notified me that they had a large number of 121H baskets available for $20 a pop. I bought a significant number of them, reconed them as 2203H's and used them in custom sound systems driven by Adcom GFA amplifiers. I sold my very last pair a few years ago. I can't imagine what I must have been thinking at the time, except that maybe having a dozen different subs sitting around doing nothing was somehow a bad thing.

  3. #3
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503
    Quote Originally Posted by Giskard
    Absolutely not. The response is rock solid down to ~ 30 Hz. A high pass filter set in the 20 to 30 Hz range will protect the transducer below resonance thereby increasing mechanical power handling.
    .........
    Running them that way in parallel will increase their maximum SPL by ~ 6 dB.
    Sounds like a killer system

  4. #4
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503
    Red = 2,8 qu ft, tuned to 30Hz
    Green = 1,8 qu ft tuned to 31 Hz (3" port, 7" duct)
    Yellow = 1,8 qu ft tuned to 31 Hz (3" port, 7" duct) with Submodule Bass EQ

    Hhhmmm
    Attached Images Attached Images  

  5. #5
    Obsolete
    Join Date
    Apr 2003
    Location
    NLA
    Posts
    12,193
    Don't forget your low pass filters when looking at subs.

    If you are looking for more extension (and poorer transient response, power handling, and group delay) then use a 6th order alignment.
    Use your 5234A set to bump at 20 Hz and tune your enclosure to 20 Hz.

    Red = 2.8 cubic feet tuned to 30 Hz with 2nd order Butterworth low pass at 80 Hz.
    Grn = 2.0 cubic feet tuned to 20 Hz with 2nd order Butterworth low pass at 80 Hz and 2nd order high pass at 20 Hz (Q=2).
    Attached Images Attached Images  

  6. #6
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503
    Clear Giskard,

    thanks for help.

    I do not necessarily look for more extension but need amps anyway and thought with the bass EQ of those sub modules I can keep the cabinets smaller.
    They should somehow "fit" to the 4313.

  7. #7
    Obsolete
    Join Date
    Apr 2003
    Location
    NLA
    Posts
    12,193
    Can you provide a technical link to the sub modules? I'd like to see how they can be manipulated.

    Thanks.

  8. #8
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503
    This is on alternative
    http://www.monacor.de/en/produktseit...pr=EN&typ=full
    Maybe one is enough for two 2203 in parallel ??

    This is another, better one:
    http://www.hypex.nl > Products > Subwoofer Amps > HS200

    or 2 of those little wonders http://www.hypex.nl > Products > Subwoofer Amps > DS1.2
    The response measurement of the DS1.2 can be seen here
    http://www.visaton-bausaetze.de/hifi/verst100.htm#ds12

  9. #9
    Senior Member Ralf's Avatar
    Join Date
    Nov 2003
    Location
    Germany
    Posts
    267
    Quote Originally Posted by Giskard
    Don't forget your low pass filters when looking at subs.
    Hi Giskard,

    how can I setup the filter parameters in BBP?

    I`ve tomatos on my eyes....
    16 Hz can not be substituted

  10. #10
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503
    I found 2 Fender 92577H Baskets. They take the E120 kits according to the transducer parts list.

    If I remeber right these damned E120s have a thicker magnet than the 2202, 2203, 2204 baskets. Right?

    So I shouldn't use those for my 2203 cone kits?

  11. #11
    Senior Member Guido's Avatar
    Join Date
    Apr 2003
    Location
    Germany
    Posts
    2,503
    Hi Giskard!

    I need to bring this up again as the 2202 baskets are finally located
    Sub module is already here http://www.monacor.de/en/produktseit...pr=EN&typ=full

    Could you post a screenshot how to setup the filter parameters in BBP?

    I want to experiment a bit before I start to cut wood. I think more in the 6th order alignment direction as a 2x3 quft sub is too big.

  12. #12
    Obsolete
    Join Date
    Apr 2003
    Location
    NLA
    Posts
    12,193
    Hi Guido!

    Quote Originally Posted by Guido
    Could you post a screenshot how to setup the filter parameters in BBP?
    I run the active filters through pspice to get their voltage drive and then convert them to .iad files for bb6p to read. You have to put a specific header in the file so an example file is attached for you to look at.

    Here's a 6th order assisted alignment for a 2203H - 1.6 cu ft tuned to 26 Hz with 126 Hz low pass filter and 26 Hz high pass bump filter.
    Attached Images Attached Images   
    Attached Files Attached Files

  13. #13
    Obsolete
    Join Date
    Apr 2003
    Location
    NLA
    Posts
    12,193
    Another example:

    Dual 2203H in 3.2 cu ft tuned to 26 Hz with JBL BX63.
    Attached Images Attached Images   

  14. #14
    Obsolete
    Join Date
    Apr 2003
    Location
    NLA
    Posts
    12,193
    Guido - I might run dual drivers in a single volume in this particular instance in order to get the correct port/duct fitted. Separating the volumes could make tuning tough because the volumes are so small.

  15. #15
    RIP 2011 Zilch's Avatar
    Join Date
    Jun 2004
    Location
    Berkeley, CA
    Posts
    9,963
    Is the Citation 5.4 a good model for 124/2203? Do we know the box size and port dimensions?

    [Zilchster ALSO forgets what driver was in those 12" subs.... ]

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 2235 subs - standard ported alignment Vs EBS
    By Doogster in forum Lansing Product General Information
    Replies: 12
    Last Post: 01-16-2005, 02:29 AM
  2. Searched to no avail - where to get 2203 recones?
    By cgaither in forum Lansing Product Technical Help
    Replies: 1
    Last Post: 12-29-2004, 06:00 AM
  3. 2242's for top right & left subs
    By JuniorJBL in forum Lansing Product General Information
    Replies: 13
    Last Post: 02-18-2004, 01:23 AM
  4. 2204 recone in 2203
    By sa660 in forum Lansing Product Technical Help
    Replies: 1
    Last Post: 04-25-2003, 10:55 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •