Page 40 of 58 FirstFirst ... 30383940414250 ... LastLast
Results 586 to 600 of 864

Thread: Project M2 DIY Thread

  1. #586
    Senior Member pos's Avatar
    Join Date
    May 2007
    Location
    France
    Posts
    2,628
    Stunning work Leslie !

    Quote Originally Posted by lesliew View Post
    mid range and bass will be directed to a Sub 18.
    everything under 800Hz will be handled buy the subs for the center channel?

  2. #587
    Member
    Join Date
    Jul 2017
    Location
    Florida
    Posts
    65
    Quote Originally Posted by pos View Post
    Stunning work Leslie !


    everything under 800Hz will be handled buy the subs for the center channel?
    Correct, that's how we planned it.

  3. #588
    Senior Member
    Join Date
    Feb 2018
    Location
    Annapolis, MD
    Posts
    194
    Quote Originally Posted by baldrick View Post
    Now with paint
    Out of curiosity, is your waveguide sitting a little proud? I ask because it seems, to me, that ribs on the back of waveguide would hit the opening you provided. I seem to recall ours needing to be a bit wider that what it appears to be on yours. Everything else looks nice though.

  4. #589
    Senior Member
    Join Date
    Feb 2018
    Location
    Annapolis, MD
    Posts
    194
    Quote Originally Posted by lesliew View Post
    Correct, that's how we planned it.
    While we cloned the Sub 18 (did you as well or did you just obtain factory units?) I never even checked the response above 120Hz. How well will they do up to 800Hz?

    Your craftsmanship is outstanding! Somebody is very lucky to have you building them!

    -Steve

  5. #590
    Member
    Join Date
    Jul 2017
    Location
    Florida
    Posts
    65
    Quote Originally Posted by sguttag View Post
    While we cloned the Sub 18 (did you as well or did you just obtain factory units?) I never even checked the response above 120Hz. How well will they do up to 800Hz?

    Your craftsmanship is outstanding! Somebody is very lucky to have you building them!

    -Steve
    Steve,

    Whilst I was asked to come up with a Sub 18 clone and might still do so, I actually found someone in CA selling 3 of them factory new for $1799 each so it really didn't make much sense. Can't really comment on the SUb 18's performance in that range since I didn't get to test it.

    Now if I could find a couple of JBL’s 2269H for a lot less than what their going for at $900 a piece I wouldn't have hesitated.

  6. #591
    Senior Member baldrick's Avatar
    Join Date
    Feb 2006
    Location
    Haugesund, Norway
    Posts
    824
    Testfit of horn and woofer:
    Attached Images Attached Images  

  7. #592
    Senior Member
    Join Date
    Feb 2018
    Location
    Annapolis, MD
    Posts
    194
    Looks good. Round thing in round hole while rectangle thing in rectangle hole!

  8. #593
    Senior Member srm51555's Avatar
    Join Date
    May 2013
    Location
    Wisconsin
    Posts
    623
    Looking good!!

  9. #594
    Senior Member pos's Avatar
    Join Date
    May 2007
    Location
    France
    Posts
    2,628
    Quote Originally Posted by sebackman View Post
    D2 and 2451SL in the same grapgh.
    Attachment 80368
    Hello Rob,

    Would you by any chance have a higher resolution picture of that measurement (ie not compressed by the forum publication engine), possibly including the <500Hz range, or maybe a data export from dats?

  10. #595
    Member sebackman's Avatar
    Join Date
    Feb 2004
    Location
    Europe
    Posts
    675
    Hi POS,

    Email sent with all data. Share as you see fit.

    Kind regards
    //Rob
    The solution to the problem changes the problem.
    -And always remember that all of your equipment was made by the lowest bidder

  11. #596
    Administrator Robh3606's Avatar
    Join Date
    Apr 2003
    Location
    Rocinante
    Posts
    8,170
    Could you please post the 2451SL on the horn no EQ?? Would love to see just how close the 476 Mg and the 2451SL measure on the same horn. My guess is close but would really like to see an actual measurement.

    Thanks Rob
    "I could be arguing in my spare time"

  12. #597
    Senior Member pos's Avatar
    Join Date
    May 2007
    Location
    France
    Posts
    2,628
    Quote Originally Posted by Robh3606 View Post
    Could you please post the 2451SL on the horn no EQ?? Would love to see just how close the 476 Mg and the 2451SL measure on the same horn. My guess is close but would really like to see an actual measurement.
    Hello Rob,
    If you PM me your email address I can forward you Rob's measurements.
    I was looking for impedance measurement so I did not find what I was looking for there, but your mileage may vary

  13. #598
    Administrator Robh3606's Avatar
    Join Date
    Apr 2003
    Location
    Rocinante
    Posts
    8,170
    Hello Pos

    Will send you a PM in the mean time as another reference here is a 476Mg on the M2



    Rob
    Attached Images Attached Images  
    "I could be arguing in my spare time"

  14. #599
    Senior Member pos's Avatar
    Join Date
    May 2007
    Location
    France
    Posts
    2,628
    Thank you, that is a nice complement to Rob's impedance measurement here:
    http://www.audioheritage.org/vbullet...303#post413303

    Surprisingly the peak positions are closer to the D2430K than to the 16 ohm 2451SL...

  15. #600
    Senior Member pos's Avatar
    Join Date
    May 2007
    Location
    France
    Posts
    2,628
    A question for those how 3D-printed their ports based on the STL files.
    What printing parameters did have success with? (material, infill, layer height, thickness, etc.)

Thread Information

Users Browsing this Thread

There are currently 2 users browsing this thread. (0 members and 2 guests)

Similar Threads

  1. JBL LN3 Project, *Official Thread
    By Nightbrace in forum Lansing Product DIY Forum
    Replies: 58
    Last Post: 07-13-2016, 03:08 PM
  2. Fundraising request; donations to Lansing Heritage Project May loudspeaker project
    By mikebake in forum Lansing Product General Information
    Replies: 7
    Last Post: 04-21-2011, 12:37 PM
  3. Project May, similar privat project?
    By Flodstroem in forum Lansing Product DIY Forum
    Replies: 14
    Last Post: 02-21-2007, 03:42 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •