Page 1 of 7 123 ... LastLast
Results 1 to 15 of 97

Thread: JBL 4344 Clones

  1. #1
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171

    JBL 4344 Clones

    Here some picture of the JBL 4344s I recently finished.

    I’d like to start by thanking all the DIY’s who post in this forum as without your contributions my project would not have been possible!

    Components 2235, 2123, 2426H, 2405, DIY charged couple cross-overs.

    I used the plans from Ayaboh – fabulous saved many hours/days/weeks of planning. I did not really deviate from them.

    Wood used 1” MDF for all panels 3/4 in Baltic birch for the baffle, 5/8 Baltic birch for the 2123 dog box and panel bracing, walnut veneer and trim. Stainless Steel for the LPAD focial, 2405 mounting plate and 2308 lens. White birch veneer stained black for the baffle.
    Attached Images Attached Images      

  2. #2
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    Everyone like tools, here’s the machine I used for the project members from down under may recognize it. I bought it back in the late 80’s for my last speaker project. It’s as accurate as any real saw/router table and folds down and can be put away for those of us that can’t dedicate space to a permanent workshop. Drawback is that no third party jigs will fit; you have to make your own. The extension table is wonderful as ripping a 4x8 is easy. Well it was when I was younger for this project I went to my local RONA and had all the pieces cut close to the size and then made all the final cuts at home – my version of quality control. Beside do you know how much a 1” 4x8 of MDF weights?
    Attached Images Attached Images  

  3. #3
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    The dog box ready to be assembled.
    Attached Images Attached Images  

  4. #4
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    On the back panel I inserted dowels where the screws for the Speakon connector and the battery box will be located.
    Attached Images Attached Images  

  5. #5
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    I clamped the back access panel frame pieces in to place to get the correct fit.
    Attached Images Attached Images  

  6. #6
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    I disassembled the mock up without disturbing the frame pieces and then drilled the dowel holes through the frame and in to the panels. Somewhat unorthodox but it was late in the fall and I was in a hurry.
    Attached Images Attached Images  

  7. #7
    Senior Member martin2395's Avatar
    Join Date
    Apr 2012
    Location
    Europe
    Posts
    928
    Lovely!
    It's only a pity that people use that ugly unit layout
    I went with the 4343 just because of that, the other ones were giving me a slight OCD attack.

  8. #8
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    Not sure why I was in a hurry as I stalled over the winter doing the cross overs. I have no experience with building crossovers and muddled my way through it. So I started with mock ups (left) and progressed to final version (right).

    Much thanks to Chas who provided much guidance with the cross overs!
    Attached Images Attached Images  

  9. #9
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    This is an easy way to get the lacquer off the coils. Let the wire sit in the furniture stripper (water based) 15 to 25 minutes depending upon how thick the lacquer is and then brush it off with a brass bristle brush. Worked great!
    Attached Images Attached Images  

  10. #10
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    I stacked the 2123 xover on top of the 2405 and 2426 circuits.
    Attached Images Attached Images  

  11. #11
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    First pass at testing the circuits
    Attached Images Attached Images  

  12. #12
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    Second pass with all the wiring complete and ready to be installed, Note the terminal block installed on top of the dog box. I also color coded all the wiring with shrink wrap to ease the correct wiring so even if you lose the wiring diagram if you follow the color coding things will still work.
    Attached Images Attached Images  

  13. #13
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    Battery Box

    I used a 9 volt guitar battery box mounted on the back panel to make things easy.
    http://www.guitarpartsresource.com/electrical_other.htm

    The box itself is deeper than one inch so I had to manufacture an internal cover with connections to inside the cabinet.
    Attached Images Attached Images  

  14. #14
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    Here I’m gluing the battery box cover on the back cabinet panel.
    Attached Images Attached Images  

  15. #15
    Senior Member christo's Avatar
    Join Date
    Mar 2010
    Location
    Toronto, Canada
    Posts
    171
    To get the wires in to 2123 I used speaker binding posts
    Attached Images Attached Images  

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Westlake TM1/TM3 clones
    By cooky1257 in forum Lansing Product DIY Forum
    Replies: 41
    Last Post: 05-09-2008, 07:55 AM
  2. Clones
    By Zene in forum Lansing Product DIY Forum
    Replies: 57
    Last Post: 12-15-2007, 05:11 AM
  3. 2405 UHF Clones
    By witoman in forum General Audio Discussion
    Replies: 34
    Last Post: 10-11-2007, 04:25 PM
  4. New BX63a Clones ?
    By LE15-Thumper in forum Lansing Product Technical Help
    Replies: 15
    Last Post: 09-09-2004, 09:14 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •