Page 1 of 2 12 LastLast
Results 1 to 15 of 25

Thread: 375 questions

  1. #1
    Senior Member jblwolf's Avatar
    Join Date
    Apr 2003
    Location
    Michigan
    Posts
    214

    375 questions

    Greetings to all!,
    Over the years I have acquired a few 375 drivers from the late 50's to the late 70's,and noticed some differences,

    picture1-I have this 375 that has marking on it and some of the later models do not,

    what do these markings mean?

    2-can the year of manufacture be found with the number on the diaph?

    and my last question is

    -on the earlier models, on the inside of the cap(bell)it looks like felt was used to line the cap,while on later models foam was used,why the change,was foam better than felt?,are there any differences in the overall sound using the felt vs foam?

    Wolf
    Attached Images Attached Images  

  2. #2
    Senior Member jblwolf's Avatar
    Join Date
    Apr 2003
    Location
    Michigan
    Posts
    214
    picture 2
    Attached Images Attached Images  

  3. #3
    Senior Member
    Join Date
    Apr 2003
    Location
    GTA, Ont.
    Posts
    5,108

    "Tolerance Measurements"

    Hi jblwolf

    Well, I don't know if foam is better than felt. I do know it's easier these days to source foam . Can't help on matching age to diaphragm numbers.

    The 4 numbers , matching the 4 directiomal axis (NSEW) represent ( in .01" increments - I believe ) how far off from "book" the gap width actually measures . I've never seen these numbers climb into the "4"s , so I imagine that's when QC at the factory kicks in and "rejects" the driver for retail release .

    I've never seen a "tolerance number" on the phase plug like your picture shows - but it makes sense that it's also checked .

    regards <. Earl K

  4. #4
    Senior Member jblwolf's Avatar
    Join Date
    Apr 2003
    Location
    Michigan
    Posts
    214
    Thanks Earl,
    I'm hoping someone out there in the forum has insight in to these questions,I've been hooked on JBL for years and didnt have any where to go to find some of answers for questions that have bugged me for years.as for the foam in the cap,the real down side is when it goes bad,what a mess it can make,I have noticed the sound seems more mello/not has bright when the cap has the foam in it,I'm wondering if anyone has noticed the same thing,I have a few compression drivers that have marking(mostly the late 50's-early 60's stuff)on the phase plug & mounting plate,all of the drivers that I have from the late 70's-80's dont have any markings-did JBL change the standard or come up with a better way of putting them together?WOLF

  5. #5
    Senior Member
    Join Date
    Apr 2003
    Location
    GTA, Ont.
    Posts
    5,108

    "Snow Boots"

    Heh Wolf
    Maybe all your later magnets have perfect gaps. I have one or two like that. All my 2440/1 drivers are late 70's vintage. One just never knows about some of these things. Manufacturing tolerances might have become tighter leading to the unmarked series of drivers you have. Or, another explanation could be that they were hand selected for sale to a large touring company-customer like Clair Bros. / ShowCo / A1 Audio / Maryland Sound / Audio Analysts / ,,, any of the larger companies who might have had the leverage to get " hand-picked lumber" . Do you know the "pedigree" of your drivers ?
    Re; foam/felt,,, there's so much open-cell foam around these days , that I just find something handy and cut an appropriately ( oversized ) circle from it. I use a friction fit since I believe the glue originally used caused the chemical reaction that led to the original "particulant" problem . Appropriate thick "felt" is more difficult to find. I've kept a casual lookout for it around here ( Toronto ). I thought being in the land of snow & ice, that it could easily be found as felt snow boot-liners. I must be a couple of decades out of step or in the wrong region or I last searched in July.
    Maybe Winnipeg is hoarding the available supply waiting for their next ice-age .

    regards <> Earl K

  6. #6
    Senior Member jblwolf's Avatar
    Join Date
    Apr 2003
    Location
    Michigan
    Posts
    214
    I would have to say 95 percent of the drivers I have came from local estate sales or the original owners that got them at a local dealer and built their own systems,theses are all home models,not pro models,I think as time went on,JBL changed the standard and found "close enough" was good enough,I have seen a few"b"stock items that should have never left the factory,Wolf

  7. #7
    Senior Member
    Join Date
    Apr 2003
    Location
    Winnipeg Manitoba Canada
    Posts
    2,291

    Wink Winnipeg

    He was that a Toronto verses Winnipeg snipe???

  8. #8
    Senior Member
    Join Date
    Apr 2003
    Location
    GTA, Ont.
    Posts
    5,108

    "Portage & Main"

    Hi John
    Yes , I guess it was. But at least I know where Portage & Main is , about the "Golden Boy" statue and Louis Reil .
    My memory of "Felt Boot Liners" comes from buying them at the old "Army & Navy" stores that have disappeared from the Cdn west .

    regards <. Earl K

  9. #9
    JohnH
    Guest
    What is the specification for the gap width (on the 2440s & 2441s)?

  10. #10
    Senior Member
    Join Date
    Apr 2003
    Location
    Winnipeg Manitoba Canada
    Posts
    2,291

    Smile portage +main

    There is a United army surplus store just up the street from the golden boy. They were never connected with the stores out west but they have the same concept and they have the liners you speak of

  11. #11
    Senior Member
    Join Date
    Apr 2003
    Location
    GTA, Ont.
    Posts
    5,108

    Gap Sizes

    Hi JohnH

    According to a JBL note from 9/77 ( rev. A ) they were

    .031" for the le85/2420, le175/2410/2460/2461/2470

    .036" for the 375/2440

    .043 for the 2480, 2482, 375AB, 375(F?)H

    I just looked at a "Service Procedure" note from 8/82 . It mentions that some older compression drivers " may also be found to have narrow gap top plates and current (1982) diaphragms will not fit these units properly ". It doesn't say what type of compression drivers or what the older gaps measurements were. Just some more unsubstantiated info to support the notion why the older stuff does/did sound different/better ( tighter tolerances ?) .

    regards <> Earl K
    Last edited by Earl K; 06-20-2003 at 03:47 PM.

  12. #12
    Senior Member jblwolf's Avatar
    Join Date
    Apr 2003
    Location
    Michigan
    Posts
    214
    Hey Earl,
    Can we find out what the gap width and flux density is for a early 60's 375 is,verus say late 70's-early '80 375-2240 is?this may give some insight to why changes were made,I remember buying a diaphram(I think it was for a Blue 375-1962??) around 1984 that had the diamond surround and it would not fit in the gap,at the time I was told I needed to order the "old style"part,the replacement did not have the diamond surround and it dropped right in- Wolf -by the way still no responce to the other questions,has the forum been stumped?

  13. #13
    Senior Member
    Join Date
    Apr 2003
    Location
    GTA, Ont.
    Posts
    5,108
    Hi Wolf
    A lot of the people that post here listen to 1.75" diaphragmed compression drivers vs the larger 4" type. I, among others would love to know the actual gap sizes for these older 375 drivers. This info was apparently lost at JBL in the big earthquake of 199? .
    Now, the fact is , you seem to have a good cross-section of these vintage drivers ; ( meaning - it may be up to you to do the measurements & let us know ,,, not exactly what you wanted to hear , I imagine ) . Automotive supply houses will sell spark plug gauges that are non-magnetic in the appropriate sizes.

    There is a spec sheet in the library that states some tech info including the magnets' flux level . I don't know the year of publishing, but it's still the most concise description of a 375 that I'm aware of .

    All my 2440/1 variants have stock foam/felt laminated pads. The foam is glued to felt that is in turn glued to the back-cap.

    regards <> Earl K

  14. #14
    Senior Member jblwolf's Avatar
    Join Date
    Apr 2003
    Location
    Michigan
    Posts
    214
    Hi Earl,
    Your right,I really didnt want to hear that,my blood pressure hits the roof every time I take one apart,the pics I posted were from what I was told is a 1965-375,and it is back in service,at this time I'm using all of the older 375's(60's stuff) I have and it may be awhile before a get a chance to do some measurements to find the gaps,I did a little looking around the site and found some info,per bulletin b-1 1954 flux density for the 375 was 21000 gauss,that was also the case for 1956,I couldnt find any info for the 60's but by1973 the flex density had changed to 20,500,but still no gap info for early models,I have always been a fan of the 4" driver,and a 537-500 or 509 horn,I really never care for the smaller horns like the HL93,seemed to compress the sound,like it coundnt breath while the 500 or 509 really opened up the mids,like you right there,I'm still playing around with my 6 channel surround,I did finally settle on 2 le15,2 375 and 4 077 for my front channels,I hope to finish the rest of the channels before to long and post the the pictures,Best Regards -JBLWOLF

  15. #15
    RIP 2010 scott fitlin's Avatar
    Join Date
    Apr 2003
    Location
    Brooklyn NY
    Posts
    4,343

    Question

    I have two 2440 drivers, and the rest of my stuff is 2441. Now one day I went to take out the original 2440 diaphragm and I put in its place the 2441 phragm. In the 2441 driver its a snug fit when you put the phragm in. On the 2440 assembly it slipped right in!

    So I listened to this 1973 vintage 2440/w 2441 phragm and I swore it had a sweeter sound to it.

    Does the 50,s and 60,s stuff have yet still a different sound?

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. JBL 375 vs 2441?
    By tv506 in forum Lansing Product Technical Help
    Replies: 30
    Last Post: 06-22-2011, 06:55 AM
  2. My First Post (aka: questions, questions...)
    By maxjax in forum Lansing Product DIY Forum
    Replies: 12
    Last Post: 08-15-2008, 10:25 PM
  3. Two Questions
    By JBLROCKS in forum Lansing Product Technical Help
    Replies: 2
    Last Post: 02-13-2005, 09:17 PM
  4. 2 in driver questions
    By lfh in forum Lansing Product Technical Help
    Replies: 6
    Last Post: 08-25-2004, 02:03 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •