Page 1 of 2 12 LastLast
Results 1 to 15 of 19

Thread: Series resistor for horn driver

  1. #1
    Senior Member
    Join Date
    Apr 2011
    Location
    Leesburg, VA
    Posts
    322

    Series resistor for horn driver

    I'm using TD-2002 drivers in DIY speakers using an active crossover. They were connected directly to the horn amp, but I noticed that the horn seemed to "stick out" a little at times, especially when reproducing female vocals. I tried a small series resistor from the amp to the horn drivers, and with about 2.7 ohms that fixed the problem. I'm happy that the solution was so easy and inexpensive, but I would like to understand the theory. My guess is that I'm "tuning" the decay time (waterfall) of the horn drivers to better match the woofers in the crossover region.
    Oppo BDP-95 DCX-2496 RMX-850 Parasound A21 First Watt J2 Dayton RSS390HF-4 MTM Quads of SEAS W18E001 511Bs TAD TD-2002

  2. #2
    Senior Member
    Join Date
    Apr 2003
    Location
    GTA, Ont.
    Posts
    5,109
    I'm using TD-2002 drivers in DIY speakers using an active crossover. <<<<snip>>>>

    Specifically, which Lansing related company makes this driver ?


  3. #3
    Senior Member HCSGuy's Avatar
    Join Date
    Jan 2009
    Location
    Bend, OR
    Posts
    752
    By adding a series resistor to the horn driver, you simply dropped the level of the horn driver - same as if you turned it down from your active crossover or the gain control on your amplifier. A resistor by itself has no time component.
    That the internet contains a blog documenting your life does not constitute proof that your existence is valid. Sorry.

  4. #4
    Obsolete
    Join Date
    Apr 2003
    Location
    NLA
    Posts
    12,193
    Quote Originally Posted by Earl K View Post

    Specifically, which Lansing related company makes this driver ?

    Altec Lansing aka James B. Lansing Sound aka Technical Audio Devices Laboritories.

    Someday someone should draw a family tree of this stuff.

  5. #5
    Senior Member
    Join Date
    May 2007
    Location
    Ingolstadt in Germany
    Posts
    456

    Data sheet required, ...

    ... especially with the different Q factors, Qe, Qm, Qt and Re.

    The resistor modifies the Qt of the driver, makes it greater. If that is SIGNIFICANT here is another question.

    The modified Qt lowers the driver's bandwidth. If that is SIGNIFICANT here is another question.

    Ruediger

  6. #6
    Senior Member
    Join Date
    Jul 2003
    Location
    Orange County, CA
    Posts
    3,597
    Instead of a series resistor, how about trying a 20 ohm resistor in parallel with the driver like JBL does it?

  7. #7
    Senior Member frank23's Avatar
    Join Date
    May 2005
    Location
    The Netherlands
    Posts
    356
    Quote Originally Posted by toddalin View Post
    Instead of a series resistor, how about trying a 20 ohm resistor in parallel with the driver like JBL does it?
    This only has an effect if the driver is crossed over passively. Then a parallel 20 ohm resistor levels out the impedance peaks of the driver and lessening their impact on the crossover function.

    Connecting it in series though renders the output impedance of the amplifier useless I gues, lessening the dampening effect of the amp, thereby changing the sound?

  8. #8
    Senior Member
    Join Date
    Apr 2011
    Location
    Leesburg, VA
    Posts
    322
    Quote Originally Posted by Earl K View Post

    Specifically, which Lansing related company makes this driver ?

    Point taken, although I understand it's based on a Bart Locanthi design. Plus, I didn't know where else I'd get an answer.
    Oppo BDP-95 DCX-2496 RMX-850 Parasound A21 First Watt J2 Dayton RSS390HF-4 MTM Quads of SEAS W18E001 511Bs TAD TD-2002

  9. #9
    Senior Member
    Join Date
    Apr 2011
    Location
    Leesburg, VA
    Posts
    322
    Quote Originally Posted by HCSGuy View Post
    By adding a series resistor to the horn driver, you simply dropped the level of the horn driver - same as if you turned it down from your active crossover or the gain control on your amplifier. A resistor by itself has no time component.
    I've been tweaking the horn level to be constant as I experiment.
    Oppo BDP-95 DCX-2496 RMX-850 Parasound A21 First Watt J2 Dayton RSS390HF-4 MTM Quads of SEAS W18E001 511Bs TAD TD-2002

  10. #10
    Senior Member
    Join Date
    Apr 2011
    Location
    Leesburg, VA
    Posts
    322
    Quote Originally Posted by toddalin View Post
    Instead of a series resistor, how about trying a 20 ohm resistor in parallel with the driver like JBL does it?
    I added an 18 ohm resistor directly across the driver, just so the amplifier doesn't see such a widely varying impedance over frequency. Other than having to change my series resistor value to get the same Thevenin impedance seen at the driver, I didn't notice much change from that addition, but it makes me feel better
    Oppo BDP-95 DCX-2496 RMX-850 Parasound A21 First Watt J2 Dayton RSS390HF-4 MTM Quads of SEAS W18E001 511Bs TAD TD-2002

  11. #11
    Senior Member
    Join Date
    Apr 2003
    Location
    GTA, Ont.
    Posts
    5,109
    I'm using TD-2002 drivers in DIY speakers using an active crossover. They were connected directly to the horn amp, but I noticed that the horn seemed to "stick out" a little at times, especially when reproducing female vocals. I tried a small series resistor from the amp to the horn drivers, and with about 2.7 ohms that fixed the problem. I'm happy that the solution was so easy and inexpensive, but I would like to understand the theory. My guess is that I'm "tuning" the decay time (waterfall) of the horn drivers to better match the woofers in the crossover region.



    - I'm aware of the opinions ( typically offered up ) over at DIY ( & H.E. ) of the necessity of adding a series resistor to TAD drivers ( when bi-amping ) .

    - FWIW, IME it is desirable ( when biamping ) to do most level matching( & EQing ) in the passive domain . Doing so, helps assure ( that dynamically ) the separate components will play as one ( ie; work, in a much more coherent fashion ) . That circuit resistance alters system dynamics is far from universally accepted ( oddly enough ).

    - A (very) primitive formula that I use to index transducers (
    according to their "dynamics potential" ) is ;

    DPI = ( BL2 / Re ) / ( Sd / Mms ) x .5

    where;
    Sd is in sq inches
    Mms is in grams
    .5 is simply an arbitrary constant added into the formula to keep the derived numbers under 100

    ( for example ; a
    2235H is @ 32 while a 2226 sits around 51 and a 2220H comes in at @ 88 )

    - Once one gets used to using this formula , one may start to understand how a transducers dynamic behavior is impacted by something as simplistic as resistance ( hence this answer to your question ) .

    - So simply put ( IMHO ) , level matching ( & EQing ) a 110 db efficient horn-driver combo to a 95 db woofer should be done passively ( even when bia-amping ) if one wants to rebalance the dynamics of the components being used .



  12. #12
    Senior Member
    Join Date
    Apr 2011
    Location
    Leesburg, VA
    Posts
    322
    Thanks Earl.
    Oppo BDP-95 DCX-2496 RMX-850 Parasound A21 First Watt J2 Dayton RSS390HF-4 MTM Quads of SEAS W18E001 511Bs TAD TD-2002

  13. #13
    Member
    Join Date
    Feb 2012
    Location
    The Netherlands
    Posts
    52
    - So simply put ( IMHO ) , level matching ( & EQing ) a 110 db efficient horn-driver combo to a 95 db woofer should be done passively ( even when bia-amping ) if one wants to rebalance the dynamics of the components being used .

    That Throws overboard the biggest bennefit of active filtering IMO...
    I made an all passive version of the 4355 filter, sounded great, but to check where it realy ended up I went back to a full active version, same components, night and day difference, more dynamic, cleaner less constraint.
    So for now I prefer the methode of using a way bigger amp on the lowest eff driver, most of the time the low unit, in my case a 2235. Second option, using the volume controls on the amps.
    But im very well aware of the difficulties to get a horn matched properly to a cone driver , and it might be the reason I go back from a 2352 horn to and exponential version so I dont need any more passive stuff in front of it to correct it

  14. #14
    Senior Member
    Join Date
    Apr 2011
    Location
    Leesburg, VA
    Posts
    322
    I have to think the driver designer assumed the driver would be connected to a resistive attenuator with an output impedance of a couple ohms, and planned on that.
    Oppo BDP-95 DCX-2496 RMX-850 Parasound A21 First Watt J2 Dayton RSS390HF-4 MTM Quads of SEAS W18E001 511Bs TAD TD-2002

  15. #15
    Senior Member
    Join Date
    May 2007
    Location
    Ingolstadt in Germany
    Posts
    456

    What is the motivation or reasoning for this formula?

    Quote Originally Posted by Earl K View Post


    A (very) primitive formula that I use to index transducers (
    according to their "dynamics potential" ) is ;

    DPI = ( BL2 / Re ) / ( Sd / Mms ) x .5

    where;
    Sd is in sq inches
    Mms is in grams
    .5 is simply an arbitrary constant added into the formula to keep the derived numbers under 100

    ( for example ; a
    2235H is @ 32 while a 2226 sits around 51 and a 2220H comes in at @ 88 )

    What is the motivation or reasoning for this formula?

    curious
    Ruediger

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. GPA 604-8H series II or new series III with urei horn?
    By baja in forum Lansing Product General Information
    Replies: 0
    Last Post: 08-11-2008, 04:27 AM
  2. Need 800 series Altec driver info
    By CarlG in forum Lansing Product Technical Help
    Replies: 2
    Last Post: 04-14-2007, 01:23 PM
  3. Inside W series 2380 horn box
    By maxwedge in forum Lansing Product Technical Help
    Replies: 3
    Last Post: 03-11-2006, 04:54 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •