Results 1 to 7 of 7

Thread: What to do with E140?

  1. #1
    Senior Member baldrick's Avatar
    Join Date
    Feb 2006
    Location
    Haugesund, Norway
    Posts
    824

    What to do with E140?

    I just got a few E140, what kind of "hifi setup" are they usable for? Or are they only suited for PA use??

  2. #2
    RE: Member when? subwoof's Avatar
    Join Date
    Aug 2003
    Location
    fingerlakes region, NY
    Posts
    1,899

    horn driver

    I used them in my rear loaded horns ( 4530 ) back in the band rental days. 3 a side run by a crown PSA2 and it killed in clubs...

    BUT that is very non-linear and not the best choice for critical playback.

    For a club retrofit back in the mid 80's I removed the aluminum dustcaps, constructed a ring of copper using 10ga household wire and glued it between the top of the former and the cone and put a paper dust cap on. Lotsa glue.... poormans 2235.

    This was for a club playback system and they had no money for new cones...after removing the 2350 horns we made 4 wide flares out of 1/4 bent plywood screwed to 2/8's that were cut into curves and coated the back with roofing tar / sawdust.

    messy but fun. wish I had taken pictures back then.

    sub

  3. #3
    Senior Member gibber's Avatar
    Join Date
    Oct 2009
    Location
    Munich, Germany
    Posts
    168
    Nice.
    Hifi setup?
    None, really.
    Get them sold to some crafty bass player(s) - that's who they were made for and that's where they belong
    This is an eminently capable driver but imho close to unusable for HiFi, especially if the orig alu dust cap is still in situ.

    PA use is possible as bass in (multiple, stacked) W bins or as mid-bass driver in large systems. Roughly equiv to 2205H/2225H and hence also usable in scoop cabs (who wants scoops nowadays?)
    But see above for where they feel at home

  4. #4
    Junior Member
    Join Date
    Sep 2007
    Location
    Virginia Beach, Va.
    Posts
    21

    Bass player cabnet

    TUNED_15.pdf

    Just add casters and a handle for very portable bass speaker.
    Works great with D130, D140 also.
    I use two of them with a stereo system. Sounds great.

  5. #5
    Senior Member ivica's Avatar
    Join Date
    Jan 2008
    Location
    serbia
    Posts
    1,703
    Quote Originally Posted by baldrick View Post
    I just got a few E140, what kind of "hifi setup" are they usable for? Or are they only suited for PA use??
    Owing to the facts that E140-8 VC length is about 0.5" ( about 12mm), and TP is about 0.28" (7.11mm), it seems that Xmax of about 0.1" can be used under not so high distortion , what would correspond to about 100W from about over 40Hz, and owing to high efficiency ( >5%), that would be about 100W/1W ( 100W almost 120dB).
    Putting paper dust cup OVER aluminum one (in order to reduce 'metallic sound") with some amount of glue ( say 10gr or more, if possible, really about 50gr would be the best, but any additional mass is well-come.
    read in:
    http://www.audioheritage.org/vbullet...ll=1#post61037

    ) between them, and with some kind of network correction I think such driver can be useful in some descent "2-way" box. ( say with Selenium D220-Ti + HM17-25 horn), with crossover frequency about 1500Hz.
    Regards
    Ivica
    Attached Images Attached Images

  6. #6
    Senior Member baldrick's Avatar
    Join Date
    Feb 2006
    Location
    Haugesund, Norway
    Posts
    824
    The E140 is part of the 4691B speakers I bought, a 2-way system with 2425/2370.

    And yesterday I finally got time to connect them and they sound quite OK! But I agree with Ivica that placing a paper dust cap might be an OK upgrade for "hifi" use, so I guess I'll do that! (the alu dust cap on mine have been painted black in the past)

    Previous these have been used as mains speakers in a small cinema


  7. #7
    Senior Member ivica's Avatar
    Join Date
    Jan 2008
    Location
    serbia
    Posts
    1,703
    [QUOTE=baldrick;339764]The E140 is part of the 4691B speakers I bought, a 2-way system with 2425/2370......


    I think that some kind of work on the network would be well-come to be done owing to:
    -no filtering E140, looking at the N4691B network,
    -and adjusting drivers sensitivities,
    -and all the other things

    in order to get 'flat" frequency response.

    Regards iivca
    Attached Images Attached Images   

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. What to do with an E140
    By pangea in forum Lansing Product DIY Forum
    Replies: 29
    Last Post: 04-04-2007, 09:43 AM
  2. Currently available E140 replacement?
    By daveobieone in forum Lansing Product General Information
    Replies: 4
    Last Post: 03-31-2007, 03:38 AM
  3. Need T/S For JBL E140?
    By Loud & Clear in forum Lansing Product Technical Help
    Replies: 11
    Last Post: 12-22-2006, 09:36 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •