Results 1 to 8 of 8

Thread: UPGRADING THE L250 TO 250Ti SPECS?

  1. #1
    Senior Member gmarascortt's Avatar
    Join Date
    May 2008
    Location
    Seminole, Florida
    Posts
    119

    UPGRADING THE L250 TO 250Ti SPECS?

    Hello...how hard would it be to upgrade a set of L250's to 250Ti specs???
    I know the high frequency 044-1 driver is upgraded to titanium(044Ti), and I think the mid-range driver was also changed, but are there any changes needed to the crosswork network??
    Anything else I need to know?? Did they or do they make a kit for this??
    Any help or suggestions would be greatly appreciated!
    Thank you in advance! Geno

  2. #2
    Senior Member rdgrimes's Avatar
    Join Date
    Aug 2008
    Location
    New Mexico, USA
    Posts
    2,216
    JBL did at one time sell a complete kit, but they are all vanished.
    Yes, it does include a different mid driver (104H) and a different crossover board.

  3. #3
    Senior Member
    Join Date
    Jan 2006
    Location
    Montgomery, AL
    Posts
    171
    I have been trying to find a pair of N250Ti crossovers for years with no success. It would require a good bit of skill, effort and time to rebuild the N250 crossovers, but that may be your best bet unless a miracle happens.

  4. #4
    Senior Member gmarascortt's Avatar
    Join Date
    May 2008
    Location
    Seminole, Florida
    Posts
    119
    Thanks guys......I found some old threads and they pretty much answered my questions.

  5. #5
    Senior Member gmarascortt's Avatar
    Join Date
    May 2008
    Location
    Seminole, Florida
    Posts
    119
    Won't have to................just purchased a set of 250 Ti's! Thanks all!

  6. #6
    RIP 2021 SEAWOLF97's Avatar
    Join Date
    Jan 2006
    Location
    in "managed decline"
    Posts
    10,054
    Quote Originally Posted by gmarascortt View Post
    Won't have to................just purchased a set of 250 Ti's! Thanks all!
    congrats , I have a pair too

    listen at least a couple of days before you form an opinion ....THEY DON'T HAVE THE STANDARD JBL SOUND ...dont be disappointed at first.

    they are NOT punchy or forward ...rather smooth , but will perform when its called for. On much source material, they are merely GOOD ....on the right source, they are GREAT.

    they DO like lots of power and will ramp up louder than I can handle, and may expose deficiencies in the audio chain leading to the speaker wires.

    take pix and let us know of your progress .... there are lots of threads on the forum.

    DO NOT slide them across a carpeted surface or the veneer problems will get worse ... I started a thread where many good suggestions for OEM feet replacement were offered.

    Preserving 250ti veneer skirts

    http://www.audioheritage.org/vbullet...ght=250ti+feet

    L250/ti bus bar settings ?

    http://www.audioheritage.org/vbulletin/showthread.php?22661-L250-ti-bus-bar-settings&highlight=250ti+feet
    Some kind of happiness is measured out in miles

  7. #7
    Senior Member gmarascortt's Avatar
    Join Date
    May 2008
    Location
    Seminole, Florida
    Posts
    119
    Thanks for the info Seawolf! This is the second set I have owned(first set destroyed in a flood). I almost bought a set of L250's b/c I was starting to panic(Looking for 5 years)

    Quote Originally Posted by SEAWOLF97 View Post
    congrats , I have a pair too

    listen at least a couple of days before you form an opinion ....THEY DON'T HAVE THE STANDARD JBL SOUND ...dont be disappointed at first.

    they are NOT punchy or forward ...rather smooth , but will perform when its called for. On much source material, they are merely GOOD ....on the right source, they are GREAT.

    they DO like lots of power and will ramp up louder than I can handle, and may expose deficiencies in the audio chain leading to the speaker wires.

    take pix and let us know of your progress .... there are lots of threads on the forum.

    DO NOT slide them across a carpeted surface or the veneer problems will get worse ... I started a thread where many good suggestions for OEM feet replacement were offered.

    Preserving 250ti veneer skirts



    http://www.audioheritage.org/vbullet...ght=250ti+feet

    L250/ti bus bar settings ?

    http://www.audioheritage.org/vbullet...ght=250ti+feet

  8. #8
    Senior Member DavidF's Avatar
    Join Date
    Apr 2003
    Location
    Sonoma County CA
    Posts
    946
    Quote Originally Posted by gmarascortt View Post
    Won't have to................just purchased a set of 250 Ti's! Thanks all!
    That should have you grinning...

    You now own a pair of each??
    David F
    San Jose

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. L250 vs. 250Ti Crossovers
    By Andyoz in forum Lansing Product Technical Help
    Replies: 14
    Last Post: 08-11-2011, 09:12 AM
  2. L220 vs. L250 or 250Ti
    By pmakres1 in forum Lansing Product General Information
    Replies: 15
    Last Post: 10-13-2008, 04:04 PM
  3. L250 and 250TI differences ?
    By mbottz in forum Lansing Product Technical Help
    Replies: 2
    Last Post: 01-15-2007, 09:25 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •