Results 1 to 8 of 8

Thread: Best way to clean up pots on old crossovers

  1. #1
    Senior Member vettedrummer's Avatar
    Join Date
    Nov 2004
    Location
    Fraser, Michigan
    Posts
    199

    Best way to clean up pots on old crossovers

    Hey gang, I've got several JBL crossovers with pots that are very hit and miss. What's the best way to clean them up? Cheers, Frank

  2. #2
    Senior Member duaneage's Avatar
    Join Date
    Jan 2005
    Location
    The First State
    Posts
    1,585
    radio Shack sells a contact cleaner spray that work. Partsexpress.com sells switch and pot cleaner sprays too.

    You could replace them for around 10 bucks each as well.

  3. #3
    Senior Member
    Join Date
    Jul 2003
    Location
    Orange County, CA
    Posts
    3,597
    OOOOHHH! Another Corvette person on the forum!

    Pic was taken at my house during a tune-up session. The tan '64 is one of mine.




  4. #4
    RIP 2010 scott fitlin's Avatar
    Join Date
    Apr 2003
    Location
    Brooklyn NY
    Posts
    4,343
    Quote Originally Posted by vettedrummer
    Hey gang, I've got several JBL crossovers with pots that are very hit and miss. What's the best way to clean them up? Cheers, Frank
    You can use DeOxit D5 spray, but if your pots are carbon composition, I would check with JBL and see if they still have the parts in stock and just replace them if they do!

    Carbon pots will be better after cleaning, but is usually only a temporary cure!
    scottyj

  5. #5
    RIP 2011 Zilch's Avatar
    Join Date
    Jun 2004
    Location
    Berkeley, CA
    Posts
    9,963
    We need to be a bit more precise here.

    Crossover "pots" are not potentiometers, typically, but rather dual reciprocal wire-wound rheostats configured as L-Pads.

    Gotta open them up to really clean them successfully....

  6. #6
    Anthony L100
    Guest
    Quote Originally Posted by vettedrummer
    Hey gang, I've got several JBL crossovers with pots that are very hit and miss. What's the best way to clean them up? Cheers, Frank
    As Zilch says, open them up, if they are not fried then you can usually return them to as new (wirewound type) with a little contact cleaner and patience. I was surprised how DIY friendly they are. If the copper wiper is a little "soft" on the wirewound resistive element IMHO it is also OK to give it a little tweak to exert slightly more pressure, but don't overdo it! I have had good results with this approach and it keeps everything original.

    Hey, Toddalin, nice parking lot!

  7. #7
    Senior Member andresohc's Avatar
    Join Date
    Dec 2003
    Location
    Near Madison WI
    Posts
    369
    Does anyone have a list of links to other website posts on this subject like on Audioasylum or AVS or Audiokarma etc. (cleaning and repairing pots, rheostats, switches, basically corroded electronic connections in vintage gear) I would like to read anything I can on it and havent had a lotta luck finding informative sites. I gotta think there are some gurus out there that could or have posted a lot of useful tips on this.

  8. #8
    Senior Member
    Join Date
    Apr 2003
    Location
    Australia
    Posts
    7,942
    Look these things are a miserable unreliable mess at best.(and nickrome wire is not my idea of Planet HiFi for a louspeaker signal path.)

    Best you measure them there L pads after tweaked to the right levels and put in fixed value Mills resisters like JBL did in the 250

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Noisy Pots.
    By JSF13 in forum Lansing Product Technical Help
    Replies: 8
    Last Post: 11-12-2005, 08:39 AM
  2. Model 14 crossovers
    By mowntnbkr in forum Lansing Product Technical Help
    Replies: 4
    Last Post: 09-07-2005, 05:23 PM
  3. Speaking of crossovers...
    By pmakres1 in forum Lansing Product Technical Help
    Replies: 2
    Last Post: 04-25-2005, 04:56 AM
  4. Can 250TI BQ crossovers be used on 250TI's?
    By Ezel in forum Lansing Product Technical Help
    Replies: 7
    Last Post: 05-12-2003, 08:12 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •