Results 1 to 8 of 8

Thread: My new jbl 4350 style enclosure

  1. #1
    Junior Member
    Join Date
    May 2017
    Location
    australia
    Posts
    3

    My new jbl 4350 style enclosure

    [ATTACH]77156

    Hello All I have a JBL 4350 style enclosure that I want to turn into a JBL 4350 style setup.

    Drivers: JBL 2235H Mid driver JBL 2206H

    I'm thinking of putting another box on top full length of the cabinet with driver JBL 2446H + 2310, JBL 2426 H + 2307 high JBL 2405.

    Any suggestions welcome. Cross over will need to be made as well.
    Attached Images Attached Images  

  2. #2
    Senior Member srm51555's Avatar
    Join Date
    May 2013
    Location
    Wisconsin
    Posts
    502
    Welcome to the Forum. Looks like a good start.

    I always wondered if anyone would try the 2206 in a pair of 4350's. This is the route I would have went but I was never able to find a passive crossover for the 2206 specifically. DSP on the 12's and 15's in combination with the passive on top is the route I would look at now.

    Some good info here if you haven't seen it yet. http://www.audioheritage.org/vbullet...55-3155-clones

    Please keep us posted on the progress

    Thanks,
    Scott

  3. #3
    Senior Member
    Join Date
    Jul 2013
    Location
    Ca
    Posts
    483
    Quote Originally Posted by powerjbl View Post
    [ATTACH]77156

    Hello All I have a JBL 4350 style enclosure that I want to turn into a JBL 4350 style setup.

    Drivers: JBL 2235H Mid driver JBL 2206H

    I'm thinking of putting another box on top full length of the cabinet with driver JBL 2446H + 2310, JBL 2426 H + 2307 high JBL 2405.

    Any suggestions welcome. Cross over will need to be made as well.
    Hi,
    Not bad but you will need an other vent. It's not just a hole... You need two 5 inch circumference foot long vent. You could damage the woofers!
    It's more like a 4355 style...

  4. #4
    Junior Member
    Join Date
    May 2017
    Location
    U.S.
    Posts
    11
    Nice looking veneer

  5. #5
    Senior Member 1audiohack's Avatar
    Join Date
    Jul 2007
    Location
    Las Vegas Nevada
    Posts
    2,701
    Quote Originally Posted by powerjbl View Post
    [ATTACH]77156

    Hello All I have a JBL 4350 style enclosure that I want to turn into a JBL 4350 style setup....
    Hi;

    Looks like fun. I would skip the 2426-2307. The 2405 will meet the 2309-2310 just fine.

    The integration will be the trick. Get it right and it will rock.

    Oh yeah, you will want to verify the box tuning.

    It will be fun to see how you go and we'll help however we can.

    All the best,
    Barry.
    If we knew what the hell we were doing, we wouldn't call it research would we.

  6. #6
    Senior Member
    Join Date
    Feb 2004
    Location
    Land of Sunshine
    Posts
    408
    Quote Originally Posted by powerjbl View Post
    [ATTACH]77156

    Hello All I have a JBL 4350 style enclosure that I want to turn into a JBL 4350 style setup.

    Drivers: JBL 2235H Mid driver JBL 2206H

    I'm thinking of putting another box on top full length of the cabinet with driver JBL 2446H + 2310, JBL 2426 H + 2307 high JBL 2405.

    Any suggestions welcome. Cross over will need to be made as well.
    interesting cabs. I noticed there's no cut out for the HF and UHF. You could get a hartsfield type horn and put it on top of the cabs. Will look and sound awesome.

    good choice on the 2235s. Great Drivers.

  7. #7
    Junior Member
    Join Date
    May 2017
    Location
    australia
    Posts
    3

    enclosure

    Thanks guys for the input

    i will build a top box about 20-30 cm high it will be same width and length and put the HF drivers in there. I have mounted the 2235's and the 2226. I also picked up a jbl 5234a I have 800 Hz crossover card. The cabinet is very high quality. Made by a Japanese engineering firm.i think it was a cab for extra bass. So I will need another port on the front?

  8. #8
    Senior Member
    Join Date
    Jul 2013
    Location
    Ca
    Posts
    483
    Quote Originally Posted by powerjbl View Post
    Thanks guys for the input

    i will build a top box about 20-30 cm high it will be same width and length and put the HF drivers in there. I have mounted the 2235's and the 2226. I also picked up a jbl 5234a I have 800 Hz crossover card. The cabinet is very high quality. Made by a Japanese engineering firm.i think it was a cab for extra bass. So I will need another port on the front?
    Yes! Not sure about the 800Hz. With the 2235’s it’s supposed to be 290Hz 18 octaves...

    http://www.audioheritage.org/vbullet...r-Plans/page10

    http://www.audioheritage.org/vbullet...or-Plans/page9

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Everest enclosure volums vs professional enclosure guide volume
    By rab in forum Lansing Product DIY Forum
    Replies: 10
    Last Post: 01-15-2015, 12:50 PM
  2. 4350 Enclosure Plans
    By Techbot in forum System Information
    Replies: 25
    Last Post: 08-26-2006, 04:05 PM
  3. Repairing my 122A's, DIY style
    By tesla in forum Lansing Product DIY Forum
    Replies: 1
    Last Post: 09-03-2005, 10:20 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •