Results 1 to 5 of 5

Thread: Separation Anxiety

  1. #1
    Junior Member AnubisXII's Avatar
    Join Date
    Jul 2008
    Location
    Dallas, Texas
    Posts
    8

    Separation Anxiety

    Howdy pardners.
    I've got a question for youse guys. I am trying to separate a couple 150 4Cs from the cabinets they've lived in for a long long time without damaging the cork(?) gasket-looking things that lie between the speaker and the cabinet.
    They've been there since Eisenhowers presidency and they're really not ready to part from their comfort zones without totally destroying the ties that have held them together for so long.

    But yeah. I think it's just the cork that's sticking, but I really want to keep it in tact. And on one of the cabs, the cork has cracked at the mounting screws.
    But is there a way to separate this things without tearing stuff up?


    See the crack?


    And why can't I see it on this side? I would rather work on this side if I need pry these things apart. And how much force is too much?



    And advice would be appreciated.
    And please understand that I am not an idiot. I'm just really cautious, that's all. And I know that I would be an idiot if I didn't ask.

    Thank youse very much.



  2. #2
    Senior Member gsb001's Avatar
    Join Date
    Mar 2008
    Location
    Huntley ILL. Chicago Land Area
    Posts
    339
    Sorry I can't help.
    I wanted you and others to know what a great post this is. With pictures and excellent question.

  3. #3
    Senior Member Don C's Avatar
    Join Date
    Apr 2003
    Location
    Santa Rosa CA
    Posts
    1,658
    You can't see the cork from the cabinet side because the outer edge of the basket is even with the cork. I'd suggest using a putty knife. From inside the cabinet.

  4. #4
    Senior Member jbl4ever's Avatar
    Join Date
    Dec 2005
    Location
    McHenry IL
    Posts
    273
    Hello, I have had this problem before. What worked for me was to put a
    piece of tape at the starting point. Next a soft rag around the edge of the basket. Using a 1x2 piece of oak the length you can get in and start tapping
    with a hammer. Start lightly going around a couple of times. Also sliding your
    putty knife around to see if it frees up in spots. Please tap only by the
    frame supports. Just used this technique on some 18's that they silicone
    sealed in the cabinets. Took about 30 minutes per cabinet, what a PITA

  5. #5
    Junior Member AnubisXII's Avatar
    Join Date
    Jul 2008
    Location
    Dallas, Texas
    Posts
    8
    Hey, I got it, man. Yeah. I used a little Hyde putty knife and a lot of patience. Set it on the floor basket side up, and slooooooly went around the rim, sliding the scraper between the cork and the cabinet, taking about an eighth of an inch with each pass around the edge. It was really difficult not to wiggle the scraper, though. But I knew if I did, something would tear or peel. And chances are it wouldn't have been the cabinet.
    It took about 30 minutes to do the first one, but the other one came off after two passes. It probably heard what I was saying to the first one and decided that it would be best for all of us if it showed no resistance and just let go.

    I appreciate the advice.
    I'm gonna leave this up just in case someone else has the same problem.
    And if they do... The two most important things to remember are patience, patience, patience.
    Speaking of patience... Don't you think that it's about time to go donate some blood? The people there are always nice and they give you free Nutter-Butters.
    So donate. The life you save may be mine.

    Oh. The separation was successful.
    Aint they purty?


Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. JBL Performance Series
    By Titanium Dome in forum Lansing Product General Information
    Replies: 2101
    Last Post: 03-03-2019, 12:43 PM
  2. Urei 813 separation
    By mgphoto in forum General Audio Discussion
    Replies: 10
    Last Post: 06-15-2007, 08:42 AM
  3. Separation and detail parameters?
    By Regis in forum Lansing Product General Information
    Replies: 1
    Last Post: 05-05-2005, 03:11 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •