+ Reply to Thread
Results 1 to 5 of 5

Thread: Reconing a D130F

  1. #1
    Junior Member
    Join Date
    Oct 2003
    Posts
    6

    Reconing a D130F

    I need a D130F.
    I have been offered 2 baskets for $50.
    I'm here to obtain knowledge about a reconing service.

    ?? I haven't seen a reputable service recommended on this forum...if it is inappropriate to post a name-telephone nr here, can you privately post me with a recommendation (or even who to stay away from) - my email is pbennett@macnet.com (re exposing my email...I get so much spam now that any additional spam won't be noticed)

    For anyone not having a reconer's name on the tip of their tongue, what do you consider a typical cost for this service? I would assume s/h would add an additional $20 or so.

    I will wish to have the F type rubberized cone periphery and assume all reconers offer this. Comments?

    I heard that JBL no longer offers reconing service? Comments?

    What am I missing here? What can go awry buying baskets in a poke? Comments?

    Judging by watching eBay, the value of a freshly reconed D130F is between $130 and $180. My interest is NOT profiting on this but want to exchange my Peavy guitar amp spkr with the D130F and not disturb the pair of 1957 D130's which gather dust in my music room. Comments? TIA

  2. #2
    RIP 2009
    Join Date
    Feb 2004
    Location
    Rohnert Park, CA
    Posts
    3,790
    Where are you located?

    John

  3. #3
    Administrator Mr. Widget's Avatar
    Join Date
    Apr 2003
    Location
    San Francisco
    Posts
    8,402
    These guys are great.

    http://www.speakerrepair.com/ocsrepairprice.html

    Their prices are about average. The D130 recone is $182 each. One thing to look out for is frequently the "recently reconed" speakers offered on eBay are not using JBL parts. After market parts are significantly cheaper. I wouldn't use them myself, but many people are happy with them.

    Since shipping is also an issue, you should call or e-mail JBLPro and get a recommendation for a reconer in your area.

    818-894-8850
    http://www.jblpro.com/contact/form_dir.html


    Good luck,

    Widget

  4. #4
    Senior Member
    Join Date
    Mar 2004
    Location
    Sanger, Texas
    Posts
    559

    Re: Reconing a D130F

    Originally posted by Paul Bennett
    I need a D130F.

    I will wish to have the F type rubberized cone periphery and assume all reconers offer this. Comments?
    It was never a "rubberized cone periphery" treatment. We used it on the D123 as an edge damping "goop", and I used it on the "F" series for some damping, but mainly to prevent the surround from drying out and cracking - a common problem with standard JBL speakers that wound up in guitar amps before the introduction of the "F" series.
    Harvey "Hifi" Gerst
    ("Hifi" was my nickname at JBL.)

  5. #5
    Senior Member GordonW's Avatar
    Join Date
    May 2003
    Location
    Marietta/Moultrie GA USA
    Posts
    1,454
    Harvey, would you have any idea, if that Waldom/Image Comm. surround treatment "goop" is similar enough to the original JBL "goop", to work the same? It's hard to find stuff like that, that stays flexy and sticky enough to act the same. The Image stuff is the most "rubbery" I've found so far; most of the stuff I've found is more "plasticky"... it tends to get too hard when cured, and throws off the resonance of the speaker (too stiff, resonance goes too far up in frequency). I've needed this, both for repairing JBL stuff, but mainly for other more obscure speakers from other vintage brands (like the pair of Goodmans Axiom 301 12" drivers I'm working on now). Unfortunately, on those, there is no equivalent to the JBL factory recone kits... us repairers are on our own, pretty much, when it comes to parts.

    Regards,
    Gordon.
    This Is Gordon's Page: www.geocities.com/gordonwaters

+ Reply to Thread

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Reason for reconing
    By gerard in forum Lansing Product Technical Help
    Replies: 4
    Last Post: 01-03-2005, 11:33 AM
  2. Help! thread on reconing?
    By andresohc in forum Lansing Product Technical Help
    Replies: 4
    Last Post: 07-09-2004, 06:11 PM
  3. reconing in FL?
    By Hofmannhp in forum Lansing Product General Information
    Replies: 1
    Last Post: 04-05-2004, 05:01 PM
  4. reconing glue
    By Hofmannhp in forum Lansing Product Technical Help
    Replies: 16
    Last Post: 01-13-2004, 04:52 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts