Results 1 to 8 of 8

Thread: Coil varnish / Enamel Removal

  1. #1
    Senior Member
    Join Date
    Nov 2003
    Location
    Toronto
    Posts
    1,162

    Coil varnish / Enamel Removal

    Hi gang, I am preparing to start construction of some networks and one thing that drives me nuts when working wth Solen coils or, for that matter - Plitron output transformers too, is the removal of the varnish from the wires.

    I tried filing, sanding and scraping it off, and frankly it's just a pain in the butt!

    What do you folks do?

  2. #2
    Senior Member
    Join Date
    Jul 2003
    Location
    Orange County, CA
    Posts
    3,597
    Quote Originally Posted by Chas View Post
    Hi gang, I am preparing to start construction of some networks and one thing that drives me nuts when working wth Solen coils or, for that matter, Plitron output transformers too, is the removal of the varnish from the wires.

    I tried filing, sanding and scraping it off, and frankly it's just a pain in the butt!

    What do you folks do?
    Rubbing the ends of the wire with a little sand paper has always worked for me.

  3. #3
    Senior Member edgewound's Avatar
    Join Date
    Jun 2005
    Location
    Southern California
    Posts
    2,776
    Yep....keep sanding and scraping.

    Or....get a solder pot to burn and tin in one step.
    Edgewound...JBL Pro Authorized...since 1988
    Upland Loudspeaker Service, Upland, CA

  4. #4
    Senior Member grumpy's Avatar
    Join Date
    Oct 2003
    Location
    SoCal
    Posts
    5,742
    Fine grit "emery cloth" is what I used to use... (cloth-backed, sandpaper).
    A bit easier to handle than paper-backed abrasive. Easy to tear off a small
    piece if you can find a roll of it.

  5. #5
    Senior Member
    Join Date
    Nov 2003
    Location
    Toronto
    Posts
    1,162
    Quote Originally Posted by edgewound View Post
    Yep....keep sanding and scraping.

    Or....get a solder pot to burn and tin in one step.

    Yeah, I have heard of that too, although a little pricey and likely an environmental disaster waiting to happen at my house...

    hmm...maybe a blow torch?

    Grumpy, good idea! I have a roll of some plumbers sand paper (cloth backed). I'll give it a whirl.

  6. #6
    Senior Member
    Join Date
    Mar 2006
    Location
    Melbourne Australia
    Posts
    153
    Quote Originally Posted by grumpy View Post
    Fine grit "emery cloth" is what I used to use... (cloth-backed, sandpaper).
    A bit easier to handle than paper-backed abrasive. Easy to tear off a small
    piece if you can find a roll of it.
    Hello Grumpy and Chas,

    Yes fine sandpaper is a good way. You just need to make sure that the wire is as straight as possible (no kinks), otherwise you easily miss some spots and sanding becomes more difficult. I am not sure whether something like acetone (or other chem) would SAFELY strip it off.

    The solder pot is the traditional manufacturing solution. If you had to do quite a few coils and were handy you could make a special copper tip for an old soldering iron which contained a small hole into which you could melt solder. Or even drill a hole in one of those large plumbers soldering irons with a large tip to make a solder "pot".
    Have Fun - >>> Nessun Dorma - 12 years old <<<
    Best, Joe Alesi

  7. #7
    RE: Member when? subwoof's Avatar
    Join Date
    Aug 2003
    Location
    fingerlakes region, NY
    Posts
    1,899

    chemical ali

    hello - it's varnish??

    A little paint stripper and an "acid" brush and it comes right off.

    scratching and scraping are no-no's in the military / industrial world since it provides a start point for vibration cracks.

    Remember that rocket that lifted off the pad then fell down in the late 50's??

    (1) wires broke off right at the crimp point.
    (2) the engineeers forgot to take the weight of solder into the calculations..

    :o)

  8. #8
    Senior Member
    Join Date
    Aug 2003
    Location
    Santa Cruz, CA
    Posts
    301
    The folks who build ham radio kits have a similar problem. Here's the recommended way directly from one of the more popular radio kits today, Elecraft.

    Also, since I have a gas stove in the kitchen, I've used flame there to burn off the enamel then tin the ends down. I can control the heat pretty well that way, too.

    I do prefer the Solder Blob method, however.

    Cheers,

    David

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Should Field Coil Come Back?
    By Ducatista47 in forum General Audio Discussion
    Replies: 48
    Last Post: 10-28-2006, 11:23 PM
  2. powderized voice coil wires
    By Krischu in forum Lansing Product Technical Help
    Replies: 5
    Last Post: 01-08-2006, 07:56 AM
  3. Coil Centering Questions
    By New At This in forum Lansing Product Technical Help
    Replies: 11
    Last Post: 06-12-2005, 01:03 PM
  4. What is AWG of voice coil ???
    By B&KMan in forum Lansing Product Technical Help
    Replies: 10
    Last Post: 05-10-2005, 10:31 AM
  5. 2234/2235 Voice Coil Former Length??
    By GordonW in forum Lansing Product Technical Help
    Replies: 3
    Last Post: 11-23-2004, 01:14 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •