Results 1 to 9 of 9

Thread: dual ohm d130

  1. #1
    Junior Member
    Join Date
    Feb 2007
    Location
    New York, Ny
    Posts
    23

    dual ohm d130

    i recently saw a D130f that says 8-16 ohms on the label. What is this and how does it change?
    thanks

  2. #2
    Administrator Mr. Widget's Avatar
    Join Date
    Apr 2003
    Location
    San Francisco
    Posts
    9,720
    It doesn't really mean much... it was put on them during the transition between tube amps to solid state. Tube amps were primarily designed to work best with 16 ohm loads and the newer solid state gear was designed to work best with 8 ohm loads.

    JBL put the 8-16 ohm graphic on some of their speakers to let people know that they would work well with both types of amps. There were several other drivers where they simply changed the graphic from 16 ohm to 8 ohm... the driver's impedances hadn't changed, but the demands of the market place had. There has been a hell of a lot of confusion ever since.


    Widget

  3. #3
    Junior Member
    Join Date
    Feb 2007
    Location
    New York, Ny
    Posts
    23

    d130f 8-16 ohm

    So it is really an 8 ohm speaker?

  4. #4
    Administrator Mr. Widget's Avatar
    Join Date
    Apr 2003
    Location
    San Francisco
    Posts
    9,720
    There really is no such thing as an 8 ohm speaker... a driver's impedance changes with frequency and with the type of box it is in.

    If you are designing a crossover and need specific impedance info buy a woofer tester from Parts Express... otherwise don't sweat it.


    Calling a particular driver an 8 ohm unit is like calling a speaker 94dB efficient. It will likely be both of these things at some frequencies and have a much higher (like 40 ohms or more) impedance at resonance and a much lower sensitivity at lower frequencies.


    Widget

  5. #5
    Senior Member grumpy's Avatar
    Join Date
    Oct 2003
    Location
    SoCal
    Posts
    5,742
    Widget's right, but there's a fair span of frequency above resonance where a "nominal"
    impedance can be reasonably provided so that a comparison of speaker drivers can
    be made... if this span mostly doesn't fall much below 8 ohms, then I'd personally
    consider it an "8 ohm" driver (as opposed to dipping to 3-4 ohms) in terms of matching
    it with an amplifier that had issues supplying enough current for a "4 ohm" system.
    If the driver impedance mostly was north of 12 ohms (or so) I'd probably consider it to
    be a "16 ohm" driver. Attached is a plot of three 2226 drivers, specified as nominally
    4, 8, and 16 ohms (0-100 ohms vertical scale, 10-1000Hz horizontal scale). The resonance
    (~40Hz in this case) is shown for a -very- large box (100ft3) and will be modified by any
    normal-sized box (sealed, ported, or open back), as Widget also mentioned.

    Without a measurement, I'd be guessing about the driver in question...
    although some folks here with more experience with dating and marking may be
    able to get you what you're looking for... a -nominal- impedance.

    -grumpy
    Attached Images Attached Images  

  6. #6
    Senior Member
    Join Date
    Mar 2004
    Location
    Sanger, Texas
    Posts
    559
    We always considered the "nominal impedance" as the trough between 200 and 400 Hz. Of course, we lied back then, calling our 8 Ohm speakers "16 Ohms".

    When amplifiers came out with 8 Ohm taps, the easiest course was to simply relabel the speakers "8-16 Ohms".

  7. #7
    Member WTPRO's Avatar
    Join Date
    May 2005
    Location
    Boston
    Posts
    51
    Hi

    As an FYI, Smith & Larson Audio (makers of the original WT and WT2) stopped using PE as our distributor last year and moved over to MCM where the WT2 is known as the "Speaker Measurement Interface". We still retain the WT2 moniker for our own direct sales as well as moving forward with our newer test products.

    Best regards,
    Keith Larson (WtPro)
    Smith & Larson Audio

    www.woofertester.com

  8. #8
    Member
    Join Date
    Feb 2007
    Location
    long beach, new york
    Posts
    32
    [quote=Harvey Gerst;. Of course, we lied back then, calling our 8 Ohm speakers "16 Ohms"
    [SIZE=3]Does this in fact mean that most of the older alnico pro drivers marked at 16ohms actually had a nominal imp. of 8 ohms?(!) I always wondered why an LE85 was rated 8 ohms while its pro counterpart was rated 16. [/SIZE]

  9. #9
    Senior Member
    Join Date
    Mar 2004
    Location
    Sanger, Texas
    Posts
    559
    [quote=rich carnese;161893]
    Quote Originally Posted by Harvey Gerst;. Of course, we lied back then, calling our 8 Ohm speakers "16 Ohms"
    [SIZE=3
    Does this in fact mean that most of the older alnico pro drivers marked at 16ohms actually had a nominal imp. of 8 ohms?(!) I always wondered why an LE85 was rated 8 ohms while its pro counterpart was rated 16. [/size]
    I don't know about the "pro drivers", but that's the values we used in the 60's.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. 8 ohm speakers on a 4 ohm amp?
    By rcpmac in forum Lansing Product Technical Help
    Replies: 12
    Last Post: 03-05-2007, 08:29 AM
  2. Ohm rating verses volume
    By jackrhein in forum General Audio Discussion
    Replies: 0
    Last Post: 02-27-2007, 06:39 AM
  3. What year was a 4 Ohm D130 or D130F available?
    By Leroy Plymale in forum Lansing Product Technical Help
    Replies: 1
    Last Post: 01-20-2006, 10:41 AM
  4. Dual 18 studio monitor?
    By glen in forum Lansing Product General Information
    Replies: 4
    Last Post: 11-17-2004, 11:21 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •