Results 1 to 5 of 5

Thread: E120 production line - when did it start?

  1. #1
    Member Krischu's Avatar
    Join Date
    Jan 2006
    Location
    Aachen, Germany
    Posts
    31

    E120 production line - when did it start?

    When did JBL start the E120 production line? Somewhere in the 70ies?

  2. #2
    Senior Member edgewound's Avatar
    Join Date
    Jun 2005
    Location
    Southern California
    Posts
    2,776
    The use of ferrite motors for low frequency drivers other than compression drivers started in 1979 I believe.

    For sure the E-Series was in 1980, and I think 1979 was a transitioning year due to the world cobalt supply shortage from Africa making alnico too expensive to produce.
    Edgewound...JBL Pro Authorized...since 1988
    Upland Loudspeaker Service, Upland, CA

  3. #3
    Member Krischu's Avatar
    Join Date
    Jan 2006
    Location
    Aachen, Germany
    Posts
    31
    Thanks a lot! Just curious, does ceramic (ferrite) require more mass/volume/material than alnico to obtain the same magnetic field strength? (That would explain why the E120 magnet is so much heavier than the D120 one).

  4. #4
    RIP 2013 Rolf's Avatar
    Join Date
    Apr 2003
    Location
    Skien, Norway
    Posts
    2,298
    Quote Originally Posted by Krischu
    Thanks a lot! Just curious, does ceramic (ferrite) require more mass/volume/material than alnico to obtain the same magnetic field strength? (That would explain why the E120 magnet is so much heavier than the D120 one).
    Yes. If I remember correctly a woofer with 5.9 kg alnico used 8.5 kg ferrite. (2231)

  5. #5
    Senior Member edgewound's Avatar
    Join Date
    Jun 2005
    Location
    Southern California
    Posts
    2,776
    Quote Originally Posted by Krischu
    Thanks a lot! Just curious, does ceramic (ferrite) require more mass/volume/material than alnico to obtain the same magnetic field strength? (That would explain why the E120 magnet is so much heavier than the D120 one).
    Yes, you're correct. Ferrite is not as powerful as alnico magnets, but is much less expensive to produce. I'm no expert on magnets but I think the ratio of ferrite to alnico is something like 5 to 1 to get the same relative magnet strength.

    On top of this, the E-Series magnet was even a little bigger yielding about 1dB additional output in the midrange. D/K Series alnico gap flux is listed as 1.2T whereas the E-Series is 1.35T.

    The E120 is actually a more accurate driver throughout it's range. Some prefer the warmer (less midrange) tone of the D/K120...not to mention it weighs about 6 pounds less.
    Edgewound...JBL Pro Authorized...since 1988
    Upland Loudspeaker Service, Upland, CA

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. DIY Axially symmetric oblate spheroid CD waveguides, in solid Oak
    By jack_bouska in forum Lansing Product DIY Forum
    Replies: 39
    Last Post: 11-14-2010, 12:36 PM
  2. K120 reconed with E120 kit = ??
    By johnaec in forum Lansing Product Technical Help
    Replies: 12
    Last Post: 08-31-2005, 07:56 PM
  3. Almost ready to start building
    By johnaec in forum Lansing Product Technical Help
    Replies: 26
    Last Post: 09-06-2004, 05:27 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •