Search:

Type: Posts; User: Mike Caldwell; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.18 seconds.

  1. Replies
    10
    Views
    506

    If you some how hit the tweeter with full range...

    If you some how hit the tweeter with full range or almost full range pink noise at a high level it could have damage the diaphragm, same goes for the compression driver.

    If your using the word...
  2. Do you have proper high pass filter on the low...

    Do you have proper high pass filter on the low end, if the speakers are unloading/flopping from trying
    to reproduce too low of below the cabinet tuning that will make low end sound loose without...
  3. Replies
    5
    Views
    468

    We have a winner!

    We have a winner!
  4. Replies
    5
    Views
    468

    Maybe P Audio?

    Maybe P Audio?
  5. Replies
    13
    Views
    906

    Try swapping the drivers between speakers and see...

    Try swapping the drivers between speakers and see if the problem stays with the driver.

    See what the DCR measures.
    How old are the drivers, the foam may have rotted and is stuck all over the...
  6. Replies
    15
    Views
    1,749

    With that I'm going to guess there using a single...

    With that I'm going to guess there using a single pole filter per band pass, the coil is a low pass on the woofers, and a cap with some resistor padding as a high pass for each the mid and tweeter,...
  7. Replies
    15
    Views
    1,749

    Was/is the crossover just between the mid and the...

    Was/is the crossover just between the mid and the tweeter as in running the cabinet bi-amped?

    With screw terminal connections I'm going to say the cabinets were for install use.
  8. Replies
    15
    Views
    1,749

    What do they have for crossovers...if any, in...

    What do they have for crossovers...if any, in them?
    What type of input connection is on them?

    Is the rectangle cut out area a port with some sort of foam covering it
    or a blocked off cut out...
  9. It doesn't leave a hole so to speak. For...

    It doesn't leave a hole so to speak.

    For example a standard 24 db per octave filter cutoff crossover at 300hz at 450hz the signal is attenuated 12db, at 600hz it is down 24db (one octave) at...
  10. You got a real DSP!! Have you tried a little...

    You got a real DSP!!

    Have you tried a little steeper high pass cutoff, if your not all ready use a BW "butterworth" filter for the high pass, there flat out to the cutoff frequency.

    Have you...
  11. Unless I missed it somewhere in your post are you...

    Unless I missed it somewhere in your post are you high pass filtering the woofers?
    Find you boxes tuned frequency, the tone sweep method mentioned works perfect.
    Set a high pass frequency at of...
  12. Replies
    1
    Views
    368

    There are no true Thiele Small Parameters for...

    There are no true Thiele Small Parameters for compression drivers in the sense of what we're used to for speakers.
    The biggest thing to consider (and I don't know what math would be to calculate it)...
  13. Replies
    14
    Views
    2,522

    Well they have already "partnered" with BMS and...

    Well they have already "partnered" with BMS and Selenium on drivers.
  14. Replies
    7
    Views
    992

    I'm going to say an earlier model D130 based on...

    I'm going to say an earlier model D130 based on the magnet pot shape and finish.
  15. Replies
    8
    Views
    5,409

    I'm going to say no on compromising the signal. ...

    I'm going to say no on compromising the signal.

    Properly set up a DSP crossover can "fine tune" a speaker system in ways an analog crossover can never do such as driver time alignment, phase...
  16. Knock off connectors will come back and bite you...

    Knock off connectors will come back and bite you every time.
    All of my speaker connections and speaker cables are all Neutrik and that is a lot of connectors

    Even the Switchcraft and Amphenol...
  17. Replies
    2
    Views
    2,030

    I know this post is getting old but the DSi...

    I know this post is getting old but the DSi series amps were/are basically the same as the original XTi and CDi series amps only loaded with presets for the JBL movie theater series speakers.

    The...
  18. Replies
    2
    Views
    710

    From what I remember on the JBL 2301's I had you...

    From what I remember on the JBL 2301's I had you could call it a random alignment.
  19. Replies
    9
    Views
    1,700

    I almost want to say Fostex, or its just a faded...

    I almost want to say Fostex, or its just a faded aftermarket recone.
  20. I'm going to feel the hit, 17 of my wireless mic...

    I'm going to feel the hit, 17 of my wireless mic systems are all in the 600mhz bandwidth, that's just about half of my wireless inventory!

    When the 700mhz sell off happened about 10 years ago I...
  21. Replies
    44
    Views
    16,544

    Regardless of the amp choice you may want to...

    Regardless of the amp choice you may want to consider a DC blocking cap in series with the 2405. Something like a 6uf would put the cap cutoff well below the where your most likely crossing into the...
  22. Replies
    63
    Views
    84,749

    I have one of the Allen Heath Qu-Pac32 rack...

    I have one of the Allen Heath Qu-Pac32 rack digital mixers and the AR2412 expansion stage box.

    Enjoy your new mixer!
  23. Replies
    63
    Views
    84,749

    I'm curious as to what you have in the Midas box!

    I'm curious as to what you have in the Midas box!
  24. Replies
    24
    Views
    10,484

    Some peoples concept of proper packing amazes me!...

    Some peoples concept of proper packing amazes me!

    Can you hear any loose parts inside falling around when you shake the amp?
    It could be a loose screw stuck somewhere it shouldn't be, a dead rail...
  25. Replies
    24
    Views
    10,484

    In case you have not heard Crown has all but...

    In case you have not heard Crown has all but pulled out of their original Elkhart, Indiana location and moved most of the production and service operation to Mexico with a customer service center...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4