Search:

Just a thought. You could try punching one of the T-nuts out and bringing it with you to the hardware store. If you have no luck let me know. I have two extra screws for the 112s mids, I can try...

Jim, thanks for the PM explaining the situation. I know you didn't have to do that but I'm glad you did.

SeaWolf97, sorry for misinterpreting the post and directing my discontent toward you. ...

I agree. My vehicle preference was stated, sorry if that was taken offensively.




The "Yahoo" part was completely unappreciated. Not sure why you took that in a way that would cause you...

Haaa, so wait a minute, you guys actually like music too..........

Lots of great recommendations here, my tastes are wide and open from the classic to the electronica...

Try this:
Morphine, ...

Yes, you guys are definitely helping, thanks for sticking with me on all of this and sorry to be so confusing. The fact that we are dealing with the physical (the actual xover), the virtual (the...

PS: Don't get any ideas, I'm the official wingnut. That handle is officially copywrited on this site :thmbsup:

Ok, I'll try to make sense of my take on this question:
As far as the 044 is concerned, I'm confused becuase the yellow/black that is connected to the xovers negative faston HF output has a female...

Sigh,,,,, I think I'm suffering from bi-polarity...
I'm still not sure if I got it right. I'll get some kind of readable documentation of my wiring and post it for review. Thanks again :)

Thanks Boputnam, hehe, yeah here we are again :D
I think what David said was correct but misunderstood. The factory wiring had the white/black striped wires female connector on the LE5s male...

That's what I was thinking. So, it was out with the old and in with the new matched set. They don't have the large inductors but they are a really clean set, the L-pads alone were worth the...

LOL, thanks Giskard. Everything is clear now. :D

Zilch, just curious, how did you get to that link on the Harman site? I can navigate to the owners manuals but not the tech sheet you found. Only thing I could do was replace the "l112" with things...

Using the schematic posted by Zilch I was able to get to the bottom of this. The two crossovers I bought were wired correctly as was the old brown one. For some unknown reason all of the black stripe...

Thanks Zilch. I found this link too on the JBL site. The tech sheet you linked is what I really needed though. Figured I'd post this incase someone needed it....

A little more info to add before I call it a night. I did some wire tracing and I suspect (to the degree of around 90% positive that) these speakers have been running with polarity issues. What...

So with that said, has anyone has seen this in the past? Anyone know the diffeneces if any between these 3 xover configs? More to come...

Ok, I did a little searching on this but didn't get all my questions answered. Hopefully I won’t confuse everyone. So, to get this twisted story rolling here is part one:
I have two L112s that I’ve...

Thanks for correcting me Zilch, in my haste to post I mixed up the names. So here is my official "Thanks Brian". :)
Got some more questions but will start a new thread since the topic is...

Good News! Mucho gracious Señorita and Zilch. The heat did the trick. I used a heat gun but I think a blow dryer would work fine. I used a razor blade to get one corner unstuck then started with a...

I guess the next obvious question would be: If new glue is needed what should I use?

Thanks Zilch, I just got back from Sears, got a nice razor scraper for the job. So if all goes as planned I'll be ready to glue the foilcal back on after I replace the L-Pads. What's the best way...

WOW, now that's what I call service! :bouncy: Thanks for the speedy reply. I'll give the heat trick a try to see how it reacts. This would be great. I will post results when I have them.

Hi, I"m new to the forum. Just wanted to chime in to get some advice on replacing the pots that control the high and mid frequency output on some L112s. There are four screws that secure the...