Search:

Type: Posts; User: Mikhail; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    1,835

    JBL4343 attenuator to bypass

    Hello everyone!
    I am the owner of 4343. Going to replace the input terminals.
    And I want to get around to bypass attenuator settings.
    Prompt, point. Somewhere in a certain topic before I saw the...
  2. Replies
    179
    Views
    117,257

    While I am planning to clamp the wire just to the...

    While I am planning to clamp the wire just to the terminal. A bass directly to the speakers. In this regard, I want to try tinned copper.
  3. Replies
    179
    Views
    117,257

    Thank you for your advice. I think that this...

    Thank you for your advice. I think that this banana should be very convenient!
    But I think the banana to each amplifier is not suitable by the fact that the distance between the terminals is...
  4. Replies
    179
    Views
    117,257

    Looking speaker cable for 4343 biamping

    Looking speaker cable for 4343 biamping, long stretches of 5 m. While stopped at here is this cable: Belden 8477 12AWG, www.belden.com/techdatas/metric/8477.pdf
    like the fact that the tinned copper...
  5. Replies
    26
    Views
    19,961

    It can be shown in the photo as it was done? What...

    It can be shown in the photo as it was done? What additional tools required? Should I had to solder?
  6. Replies
    8
    Views
    7,293

    BMWCCA has exceeded their stored private messages quota and cannot accept further mes

    BMWCCA has exceeded their stored private messages quota and cannot accept further messages until they clear some space.
  7. Replies
    6
    Views
    7,614

    Thank you all! I got it! There is no universal...

    Thank you all! I got it! There is no universal answer. I'll take my ears in hand :D and will learn to listen and to compare and choose.
  8. Replies
    6
    Views
    7,614

    In this part yet understand, but as the ratio of...

    In this part yet understand, but as the ratio of the signal level high and low, how to configure them? Only at the hearing?
    After all, the bass level can be increased strongly, but where is the...
  9. Replies
    6
    Views
    7,614

    Ashly XR-1001 : how adjust the volume level?

    Thanks to the forum!
    I bought and received and connected my Ashly XR-1001.
    Plugged in biamping 4343, high and mid to ltube amplifier, low to the transistor in class "A".
    This is a practical...
  10. Replies
    0
    Views
    4,856

    Cross Accuphase F-5 and JBL4343

    Hello all.
    Here's a crossover Accuphase F-5 and my JBL4343, as will be good?
    What better ASHLY XR-1001 or Accuphase F-5?
  11. Replies
    13
    Views
    15,223

    Thanks for the help! See diagram! But do not...

    Thanks for the help! See diagram! But do not understand! When in an external crossover, how to move the signal?
  12. Replies
    13
    Views
    15,223

    jbl 4343 crossover schematics?

    Can anyone help me find a native jbl 4343 crossover schematics.
  13. Replies
    13
    Views
    15,223

    Thanks for the answers! I will buy ASHLY XR-1001...

    Thanks for the answers!
    I will buy ASHLY XR-1001 it near there.
    How is the signal in 4343 when switching on the outside a Cross? whether there is a drawing? What is the difference in the internal...
  14. Replies
    13
    Views
    15,223

    Active crossover for 4343, the cut?

    I want an active crossover for bi-amp for 4343.
    The cut on 300Hz.
    Here's a cross:Pioneer D-70.
    Pioneer D-70
    The cut: 250Hz and 320Hz.
    How much it will be good?
    It would be correct to connect...
  15. Replies
    21
    Views
    13,167

    Thanks

    Thanks
  16. Replies
    21
    Views
    13,167

    What does it mean: DCR 6.39 ohms?

    What does it mean: DCR 6.39 ohms?
  17. Replies
    410
    Views
    369,282

    [QUOTE=martin2395;370661]Daddy, is that you? :D...

    [QUOTE=martin2395;370661]Daddy, is that you? :D
    Not much of an original 4343 left, though - fresh 2235H, 2123H, 2450J with Radian 1245 and alnico 2405's.
    Internal cabling is changed to Van Damme...
  18. Replies
    21
    Views
    13,167

    In my case, simply can not be connected. Such a...

    In my case, simply can not be connected. Such a device amplifier. The photo shows a native connection 4-pin:
    I do not have a native plug. On the other side of the amplifier previous owner installed...
  19. Replies
    21
    Views
    13,167

    I quickly switch impedance can not, only by...

    I quickly switch impedance can not, only by soldering, on the question of how to solder a wire to the output of 4Om or 8Om?
  20. Replies
    21
    Views
    13,167

    And let's look at a specific example with my amp:...

    And let's look at a specific example with my amp: Specification of LUXMAN MB88 Luxman and my speakers JBL4343. I connect the speakers to the terminals of the amplifier 4, what do you think? It will...
  21. Replies
    11
    Views
    8,638

    [QUOTE=martin2395;370602]I use these, cheap and...

    [QUOTE=martin2395;370602]I use these, cheap and look very "high-endish":

    64144

    You can call them WBT knockoffs, they are made by Dynavox and I saw them for around €8-10 @ pair.

    For me, Japan...
  22. Replies
    11
    Views
    8,638

    Please advise me which terminals to buy and where...

    Please advise me which terminals to buy and where to buy? To price and quality was good. Hole for the wire to 6mm2 and the ability to connect Banana.
  23. Replies
    11
    Views
    8,638

    This is a good explanation, Thank you! I will...

    This is a good explanation, Thank you!
    I will change only the terminals!
  24. Replies
    11
    Views
    8,638

    Thank you for your help! So I think not only to...

    Thank you for your help!
    So I think not only to replace the terminals, and more to make a bypass regulators and it will be better for sound, you also think so? Or replace only the terminals? I use...
  25. Replies
    11
    Views
    8,638

    Terminals connections JBL4343

    Maybe this question has already been, but I have not found?
    Terminals connections. Replace or not to replace? If replace for what? Original or others? Which is better?
Results 1 to 25 of 41
Page 1 of 2 1 2