I don't think that's going to work. As a minimum a different driver on the M2 is going to give you a different impendence plot. Take a look at this thread where I have 8 ohm 2453-SL's on the PTH1010....
Type: Posts; User: Robh3606; Keyword(s):
I don't think that's going to work. As a minimum a different driver on the M2 is going to give you a different impendence plot. Take a look at this thread where I have 8 ohm 2453-SL's on the PTH1010....
Hello Rusty
It's a weird shaped room with a large walk in closet filling one corner. One speaker is close but better the other has no wall close. There is no way to get symmetry with placement...
Hello Widget
Yes it was literally staring me right in the face. The key was a simple phase test. I had been running my Heil's in the room that way and just dropped these right into basically the...
I was doing some comparisons with with my basement system and these and I just couldn't match the sense of space I was getting from the PTH1010/2453SL and these speakers. After thinking about it...
My passive speaker is not time aligned and in my case the compression drivers leads. Not worried about the time alignment. As long the summation is good through the crossover region all is well.
...
Hello
Thanks!
They use a 270us delay to time align them using the DSP for the M2. So no they don't align you would have to push back the horn a bit but then you introduce another set of...
Thanks Guys!
Rob:)
Thanks!
I had them dialed in before I finished the cabinets although I haven't powered them up yet so I don't know how lossy my cabinets were using just a couple of screws. Also hopping I don't...
One done one to go!
Rob:)
Well got a top finished and a bass veneered seem to match up well. Have to formica the bass cabinet top and bottom. Now for some lesson's learned.
I got 10mil backed veneer with psa? glue which is...
Thanks Widget!
Rob:)
Thanks Chris
Rob:)
Sanding filing and filling! Beautiful weather today! Getting a lot done both tops ready for sealing. Working on the bottoms. Have a flat black eggshell coming tomorrow for the backs and any exposed...
It's been rain, rain and more rain. Wish I could send some of it west. Just finished getting my second top routed and ready for veneer and formica. Doing walnut first then doing formica tops to...
Hello Widget
Now I went and did it got a 4x8 sheet of 10 mil flat cut paper backed walnut vernier that is pre-coated with adhesive so peel and stick. Getting 4x8 of flat black formica for top and...
Hello Widget
Yeah it's getting close on the veneer. Don't want to break them down but I should just bite the bullet and get it done. Never done it before so it will be a learning experience. What...
Been just listening. I have updated my system to include a refurbished Emotiva XMC-1 to use as my preamp in a stereo system. All of my sources are digital and I was looking for something that had...
It took weeks but I finally got my 1.8M resistors so I could charge couple the networks. Got them finished and they sound great! Now it's just the cabinets! Just did a verification to see if the...
Been listening and having fun. Added an Impedance conjugate to tame a peak, and minimize phase angle to +/- 30 degrees. Retired the PS-200 and am using a pair of Emotiva HC-1's running with balanced...
Hello Pos
Thanks!! On the 2453SL no I actually don't have any 2450's the 476's would be the only valid comparison I have. The 2453's are going downstairs in my active set-up only going to use them...
Thanks guys!!
It's a rainy day here and I have off so have been listening to them. I am really impressed just how dynamic they are. I have been doing a shoot out between my basement system and...
Well it's great when a plan comes together and it all works out. The decision to build the cabinets low tuned with a bump filter is working out very well. I get the last octave fill with no boom at...
OK back to the build! So I got the passive crossovers done and installed. When I was doing the biamp passive comp on the CD it sounded really good on some material and not quite right with others. I...
Thanks Widget!!
I found them on the site!! For next time!! I have one PCB built and tested and it's good! Was really worried about keeping the level right for a max flat response. Did a quick...
And the fun begins!! Got my crossover components so I can see if the network is right. The caps in the high pass are going to be charge coupled so large values x 2 takes up a lot of space. Wish I...