Search:

Type: Posts; User: Val; Keyword(s):

Page 1 of 12 1 2 3 4

Search: Search took 0.14 seconds.

  1. I blew my 2245H being stupid with an overpowered...

    I blew my 2245H being stupid with an overpowered amp and Soul Coughing "Rolling", a tune which has some serious LF. I sent it off to edgewound for a recone and just got it back last week. It sounds...
  2. Replies
    10
    Views
    1,822

    Since it will be awhile until I'm able to afford...

    Since it will be awhile until I'm able to afford to recone my 2245h I decided to steal the E155 out of the garage 4699B speakers so my living room sub has a driver. I'm actually looking forward to...
  3. Replies
    10
    Views
    1,822

    I had a great call with Ken yesterday. I will...

    I had a great call with Ken yesterday. I will eventually have it reconed by him...thanks
  4. Replies
    10
    Views
    1,822

    A tiny bit better...still feeling like a dope for...

    A tiny bit better...still feeling like a dope for over driving it.
  5. Replies
    10
    Views
    1,822

    Unfortunately the vc former has some minor...

    Unfortunately the vc former has some minor bubbles and some scorched marks on the vc windings. I decided to glue is back together with 5 minute epoxy knowing it might not go well. The glue up went...
  6. Thread: Speaker Safari

    by Val
    Replies
    870
    Views
    427,333

    I had a similar issue with a slightly different...

    I had a similar issue with a slightly different model of Sony headphone and was able to cheaply replace the ear pads purchased on-line...
  7. Replies
    10
    Views
    1,822

    Thank you for taking the time to lay out the...

    Thank you for taking the time to lay out the process. I could use a little more clarification as I'm having trouble envisioning how to apply the black glue.

    So if I have the speaker sitting on...
  8. Replies
    10
    Views
    1,822

    2245H Detached Spider

    I stupidly overdrove my poor 2245H playing Soul Coughing "Rollin" way too loud. The cone froze in the extended position. I pulled the driver and there is a little good news. The coil measures a DC...
  9. Replies
    2
    Views
    1,016

    Hi Matthais, I too have been thinking about...

    Hi Matthais,

    I too have been thinking about applying the 2425/2426 to the Bella Luna Diamante design. Have you had a chance to hear one? I've not found one locally to listen to here in...
  10. Thread: Jbl scl-2

    by Val
    Replies
    17
    Views
    3,765

    Sort of makes sense. So I guess that makes the...

    Sort of makes sense. So I guess that makes the Everest DD67000 a 3.5 way. :)
  11. Thread: Jbl scl-2

    by Val
    Replies
    17
    Views
    3,765

    Interesting product. What makes it 2.5 way?

    Interesting product. What makes it 2.5 way?
  12. Replies
    37
    Views
    8,049

    Sadly, no tube amps here

    Sadly, no tube amps here
  13. Replies
    37
    Views
    8,049

    I appreciate the comments and calculations. For...

    I appreciate the comments and calculations. For now, I'm planning on working on a cabinet design with no less than 3 cu ft for the E155...hopefully a bit bigger.

    I do have a question about the...
  14. Replies
    37
    Views
    8,049

    Richard - thank you for running those...

    Richard - thank you for running those calculations!
  15. Replies
    37
    Views
    8,049

    Hi Richard - Thank you for that reference doc. I...

    Hi Richard - Thank you for that reference doc. I had not seen it. I think I found my answer regarding an open/dipole configuration:
    79342

    Sounds like I'd risk damaging the driver.



    Yes,...
  16. Replies
    37
    Views
    8,049

    I appreciate that! I'm impressed that you have...

    I appreciate that! I'm impressed that you have those cabinets in the house. I couldn't swing that around here! :blink:
  17. Replies
    37
    Views
    8,049

    I hope so, when I get a minute I'll pull the...

    I hope so, when I get a minute I'll pull the driver and take a look.



    I hear you and agree with you, but, I like the challenge of holding to my design goal of smallest cabinet for these...
  18. Replies
    37
    Views
    8,049

    If I build something I will probably go the...

    If I build something I will probably go the minidsp 4x10 route with tons of shaping...
  19. Replies
    37
    Views
    8,049

    Ok. I was not considering that I could add mass...

    Ok. I was not considering that I could add mass to these cones. Is low mass the reason for the aluminum dust cover? Interesting. I'm not sure I'm down with the Hill-Billy approach but I did...
  20. Replies
    37
    Views
    8,049

    I've always liked the look of the 2342...but I...

    I've always liked the look of the 2342...but I have to say that I've become a little obsessed with the Bella Luna Diamante approach...and I have a friend with a wood lathe I can use. I'm super...
  21. Replies
    37
    Views
    8,049

    Existing cabs are about 9 cu ft. so 6 cu ft would...

    Existing cabs are about 9 cu ft. so 6 cu ft would be an improvement size-wise. Just wondering if anyone has any experience with non-tuned enclosures like H-Frame or W-Frame dipoles. I've built many...
  22. Thread: ALTEC Model 15s

    by Val
    Replies
    8
    Views
    2,135

    Nice find...and delivered too! Iím looking...

    Nice find...and delivered too! Iím looking forward to seeing what you come up with.
  23. Replies
    37
    Views
    8,049

    So it's been over 4 years since I updated this...

    So it's been over 4 years since I updated this post...and the 4699B's are still looming in my garage. Lately I've started obsessing about what is the very smallest form factor cabinet I can build...
  24. Replies
    41
    Views
    11,253

    A few years back, after the cat knocked my...

    A few years back, after the cat knocked my daughter's Apple late 2009 Macbook four feet to the ground breaking the screen, my media server was born. My daughter got a new laptop for college and I got...
  25. Replies
    45
    Views
    17,013

    Amazing! Thank you for documenting your project!

    Amazing! Thank you for documenting your project!
Results 1 to 25 of 279
Page 1 of 12 1 2 3 4