Thanks Grumpy, leads 1 and 2 on L pad = 40 ohms fully clockwise 22 ohms at the 12 oclock position and 0 ohms fully counter clockwise , again thanks
Type: Posts; User: kartsmart; Keyword(s):
Thanks Grumpy, leads 1 and 2 on L pad = 40 ohms fully clockwise 22 ohms at the 12 oclock position and 0 ohms fully counter clockwise , again thanks
i have been searching the forum for the 4430 and 4535 hf crossover diagram schematic replacing the 30ohm rheostat replaced with the 8ohm L pad does anyone who where its at ?
Thanks Rob that makes my day complete :D
I bought awhile back what was to be a pair 2123H 8ohm but after looking closer the cone is maked 66287 . 66287 is the J ? i put a ohm meter on it and it reads 4.8 ohms across the leads ? what do i...
Posted by Tre' (P) on October 5, 2013 at 17:00:22In Reply to: RE: YUP posted by Ed Schilling on October 5, 2013 at 09:34:08:
"Well, I say "not in the signal path" because the Coil and cap are...
I swapped out the E-145 for TAD 1602 with good results . so its tad 1602 2118 mid and the amt for the top i like what i here ,sounds promising . now i would love to get it all passive x-over any...
thanks Rob for your efforts and help / i'm in the process of putting on a high gloss black finish on cabinets now so it might be a little while again thanks
your the one its the original 4826 boxes same cubic ft as for subs i got a pair of 2246 18" suds
yes your correct on the front panel but with the extra bracing i used and ports made out of 3/4' stock box volume should me very close to original / as for the software i no longer have excess to ....
I'm finally getting back to this project. :applaud:i'm in the works of redoing 4628Bs the plan is E145-2118- ESS AMT-1A air motion transformer . the help I need for know is calculating the port...
I have 4 TAD 1602 drivers . I would like to recone them to 1601A or 1601B does anyone know if the baskets are interchangeable ? :dont-know:
How about a sketch of these wave-guides for us DIY guys
Just thinking /tpl-150h for replacing the 2404 in the 4628B and 2445s for low end ? :bouncy:
Grumpy thanks for the reply, I will be using these for music play back for home use . I have read in one of zilchs threads that the port tuning could be a little lower and the 8" mid could crossover...
I have a good pair of 4628b , it has a good pair of E-145s and good pair of 2218s , I have on hand a pair of 2435HPL or a pair of ESS amt 1a airmotion transformer , to replace the 2404 ,
what...
i give . please what is the answer :banghead:
Im guessing + to black for 2123 2241 2404 ? :blink:
just would like to check - what would the the polarity connections be for the drivers / 2123H 2441 2405 / and biamped 2245
Thanks for your time to answer my questions , hopefully i will get these done , I had one of the worst years of my life !!! once again Thanks !!! :D
I am finishing up my 3155 cc networks \ I have 2 questions \ 1 hooking up the Lpads does the terminal 3 go to crossover and terminal 2 go to the driver and terminal 1 go ground / as in the 4344 MK...
Been in hospital for the last 3 months looking forward to get back to this project when I'm able !
There seems to be some debate firewire VRs usb , Not so much as in preformance but cost of cable's ,Firewire can use a cheep cable where usb will need a quality cable , Is this true ?
from what I have read Dac,s do not sound alike , soft, punchy , soundstage , narrow, wide ? for the equipment I have what would work good in the $ 1000-1500 range .
I-mac for music...
Went to order part from solen everything seemed good until the shipping charges was applied, $163.00 can this be right ? :eek: E-mailed them but no reply. This will sure put this project over...
Just checking before ordering parts L4 470u is the same as .47mh ?