Search:

If you are staying passive the crossovers for that driver configuration at 800 hz would be early version 3110 pro or LX13 consumer

Hi Mike, no one has answered so here are my thoughts. If you are making the 4355 crossovers which are 1.2Khz and 10Khz points. Check out the polar response on the 2390 horn/lens combination in the...

Thanks David for the heads up as I was ready to purchase some of theirs.:thmbsup:

I forgot to post this some years ago. This reference is to the JBL H91/2307 horns. Evidently JBL changed out the castings at sometime in the series production. I have not seen it on the longer...

Info here
https://www.yumpu.com/en/document/view/22789810/technical-notes-volume-1-number-12b-polarity-conventions-of-jbl-

Positive

Hi alfmonster, the 3160 xover has a 4 ohm low frequency input. The old n500 is rated at 16 ohm for the low frequency. What horn will you be using as not many load the compression diaphragm well at...

Hello alfmonster and welcome to the LH site. A crossover that works for your components is the old legacy 3110 grey in color crossover. Not hard to find and has the 16 ohms input you are using and...

Hello Daemon and welcome to LH. As being new to the site there is info on many cabinets that you can make. It is located at the top of the page. Click on the library tag and look for cabinet...

The 2446 will have less distortion and the ability for more spl output than the 2425/26
Also the 2344 horn will exhibit better imaging and soundstage than the 2380
If you use a better horn on the...

Hello Mazza, the magnet assembly looks correct but the basket does not look like it is a JBL frame. Can be a problem if not for the depth of the recone kit

Have the earlier version 4675 with 2-2225H’s and 2360 horns 2445J mid/high drivers and 3160 crossovers. The other horn I have tried is the 2382 which is 40x120 not to bad but the 2360 does sound the...

Hello daveinfl, if the foams on the speakers are all good save your money. I have had speakers sit for sometimes almost 10 years and they still work fine. Did you check the foam on the side firing...

Hi Giuseppe, scroll down to post #6 for your information :)

http://www.audioheritage.org/vbulletin/showthread.php?2250-2307-2311-2312-Bolt-Pattern

Hello Macsic, both the 4350 and 4355 are listed at 8 ohms due to the 2202 mid bass driver. Above that driver the impedance runs around 10 to 12 ohms. The 4350 crossover is set at 9 KHz and is a 3...

I am going to relive my youth and go for the chemistry set while I listen to some more GD:D

Hello Kelossus, a company here in the states sell the adaptor needed for the 1.5” to 2”. The company’s name is US Speaker. It is made by P Audio which you may be able to find a distributor by you....

Hello and welcome. The pegs are removable but in doing so some of the particle board might come with it. Also you stand a chance of breaking them off. This then becomes a pain to get the other part...

Use to be on this site but can not find it in the Library anymore. Google search JBL crossover connections. Look for the site www.cieri.net JBL dividing network instruction manual. It is 8 pgs of...

Hello mefisto, you may want to list your wants in the Lansing marketplace for the drivers. Nice horns BTW.

Also do not see the rear gasket noodle that came with a new recone kit

Hello c10m, the one driver a the top of the photo was a E130 or E140 basket in its day. This can be seen by the mounting holes having the larger half moon clips drilled in the mounting frame. I...

I would still get the 2202’s and the 2441’s just in case you decide to build the 4355’s later. These components are getting harder to find in excellent condition. Your other component choices will...

Giuseppe check out image #10 for dimensions
http://www.audioheritage.org/vbulletin/showthread.php?11351-4350-Enclosure-Plans

Here is some info that might help you
https://jblpro.com/en/site_elements/4648a-spec-sheet...