Are you going passive or active?? I used the M2 with a 476Mg same driver family and crossed at 700Hz to the M2 waveguide. Have you taken measurements with your drivers??
Rob:)
Type: Posts; User: Robh3606; Keyword(s):
Are you going passive or active?? I used the M2 with a 476Mg same driver family and crossed at 700Hz to the M2 waveguide. Have you taken measurements with your drivers??
Rob:)
Part 2
Last version 1999
Rob
Just a little something from John Eargle
My passive speaker is not time aligned and in my case the compression drivers leads so you would delay it not the woofer. Not worried about the time alignment. As long the summation is good through...
You don't need money this is a free box program that come preloaded with lots of drivers. You can also enter new ones. It has the 2235 and Le15 preloaded not sure if you can do the passive radiator....
I don't go through a lot of gear I tend to like and keep. I have either Crowns or Emotiva in all my systems. My HT is a mix of Crown and Emotiva. I have Crowns on the 4 way active stereo mains and...
Hello BMWCCA
Yes I can only think of one time I could get those comparator lights to flash on any of them. My PS400 was driving stereo subs and I was seriously pushing the limits in my HT on a...
Hello
Thanks!
They use a 270us delay to time align them using the DSP for the M2. So no they don't align you would have to push back the horn a bit but then you introduce another set of...
Good luck with that I doubt you are going to find 4 PS-400. I have 1 PS400 and 6 PS 200 in service. The PS 400 and 3 PS 200 in my HT and 3 in a bi-amp set-up. Had most of them checked out after I...
You are going to have to run them in a box program to see which is best in the box size you can live with.
Rob :)
I tried aftermarkets years ago and the measurements were all over the place. Even if those were good you would still need the dampening pads that go under them. I would look elsewhere.
Rob:)
The only carver gear I have ever owned was the Phase 4000 preamp. I loved it but it died. On the amp front when I had my XPL's and DX-1 running I used crown amps with them and never had an issue with...
Hello Toddalin
I missed this. OK why not have to wait till I get them up and running again. They have been temporally "retired" I didn't realize that they used a 60 degree angle on the "wings"....
Hello Barry
Does it have a deeper frame and cone like say an E-145 with the extender ring vs standard frame?? Deeper cone also like an E-145?? Is it a supped up E-145 power wise??
I have never...
They must be changing the throat diameters on the Radians to 1.5" They are 1.4" and 2" available for stock drivers. Unless they drop a sleeve into the horns throats can't imagine them redoing the...
Yes they do and legacy is so important done at 10:09:10
Rob:)
They are supposed to be interchangeable main differences is power handling. Curious to see what you find, I have used 2035's and found them to be good drivers.
Rob:)
See what happens when you add a sub! Think it's good now just wait!
Rob:)
Please don't take a nice pair of vintage speakers and butcher them. Leave them be and make new cabinets.
Rob:)
You would have to change to a HL 93 2392 2" throat horn. Physical fit?? Probably. Might work out well. The horn in the stock 4333 is quite long.
Rob:)
This will get you started
http://www.audioheritage.org/vbulletin/showthread.php?29391-Hiraga-s-crossover-for-Altec-A5x
Welcome!
Rob:)
Hello Earl
Great thanks for posting them. That gives us a more complete picture of what to expect.
Rob:)
They look great! Lucky to find a pair in such good condition.
Rob:)
Found the Truextent measurements pos did them in a 2450SL core you can see the roll off. Similar to the 476Be
...