Search:

Type: Posts; User: Robh3606; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.73 seconds.

  1. Replies
    2
    Views
    68

    There is always some phase shift through a...

    There is always some phase shift through a crossover. It is aproximately 90 degrees per pole so an 18Db network will give you 270 degree's. Your best bet is to try it both ways to see which sounds...
  2. What versions of the 811 or 813 A,B or C?? They...

    What versions of the 811 or 813 A,B or C?? They may be very hard to find parts for so make sure they are in good shape before you pull the trigger. They are large format monitors so they don't...
  3. Replies
    694
    Views
    77,253

    Hello 4313B That was the plan so I could get...

    Hello 4313B

    That was the plan so I could get the offset closer to try to time align them.

    Rob
  4. Replies
    18
    Views
    855

    It's an underhung coil. You couldn't get better...

    It's an underhung coil. You couldn't get better heatsinking with the mass of the magnetic structure.
    What kind of power levels?? I run mine with 100 watts and it's more than enough and with those...
  5. Well if you are switching out the series inductor...

    Well if you are switching out the series inductor L1 of the crossover you are essentially running them full range. You need the DX-1 or another suitable active crossover to roll the woofer off...
  6. Replies
    72
    Views
    3,481

    Hello Don Can't wait to see how you like them...

    Hello Don

    Can't wait to see how you like them in your room and how flexible you find the DSP for the room EQ. Based on the DSP I have installed in a Crown XTI amp it should be quite impressive and...
  7. Replies
    694
    Views
    77,253

    I didn't source the horns. I wish! I have 2216's...

    I didn't source the horns. I wish! I have 2216's the PTH 1010's with 476Mg's. I was happy to get the box dimensions for the 2216's

    Rob
  8. Replies
    18
    Views
    855

    Or E-145's Rob:)

    Or E-145's

    Rob:)
  9. Replies
    694
    Views
    77,253

    Hello 4313B Thanks for posting that techsheet....

    Hello 4313B

    Thanks for posting that techsheet. Couldn't have been more timely. Just about ready to cut wood.

    Rob:)
  10. Hello Baron, Heather I have been using the PS...

    Hello Baron, Heather

    I have been using the PS series in my "big system" for years. I have PS-200's on the E-145's 2123's and 435Be's. I use a PS-400 on my pair of B380 clones. They sound better...
  11. Replies
    23
    Views
    1,691

    The midband response is what the sensitivity is...

    The midband response is what the sensitivity is based from and where you would match driver sensitivity. That graph is misleading. There is quite a difference in bass roll-off between the 2 drivers...
  12. Replies
    17
    Views
    973

    Hello Are you using the stock crossover?? The...

    Hello

    Are you using the stock crossover?? The main difference between the 4430/35 is the power handling down low. Tuning up at 40 hz is going to effect how the woofers sum in the first two...
  13. Replies
    38
    Views
    2,620

    With quitar pick-ups are they designed to be...

    With quitar pick-ups are they designed to be linear?? Sounds more like a MI speaker application and there are significant differences between magnetic vs VC differences in say an E-130 and a 2235 as...
  14. This is the driver line up in my 4 way active...

    This is the driver line up in my 4 way active mains. I have B380's 2235's with BX-63A up to 80Hz E-145's up to 300Hz to 2123's up to 1.5K to PTH1010's with 435Be's. Works quite well. I wouldn't get...
  15. Replies
    45
    Views
    7,042

    Hello Ivica Never tried them. Going way back I...

    Hello Ivica

    Never tried them. Going way back I used to use 2344's with aquaplased 2426's. When the 2435 showed up on Ebay I grabbed a couple of pairs purchased the ferro recharge packs and had...
  16. Replies
    45
    Views
    7,042

    Hello Paul I have a pair of 476Mg's that I...

    Hello Paul

    I have a pair of 476Mg's that I measured on PTH1010 waveguides. Take a look at where they drop off. It's no wonder that they cut in at 20K. Also notice how clean they are up above 10K....
  17. Replies
    45
    Views
    7,042

    Look here for the comparison of different...

    Look here for the comparison of different materials used for the diaphragms in a large format driver 4"

    ...
  18. Replies
    13
    Views
    1,351

    Hello Jakob Not sure aside from the fact...

    Hello Jakob



    Not sure aside from the fact that the overall impedance curve stays reasonable even with the parallel notches. I doubt that's the reason though someone else is going to have to...
  19. Replies
    694
    Views
    77,253

    You certainly have my attention, better than the...

    You certainly have my attention, better than the Arrays! Now I have to go hear a pair.



    Sounds like E-145's on steroids. Glad I got my table saw ready to go.

    Rob:)
  20. Replies
    3
    Views
    491

    Why waste a 2242 in a sealed box?? Rob:)

    Why waste a 2242 in a sealed box?? Rob:)
  21. Replies
    3
    Views
    236

    Not enough info WAG 1-1.5uf Rob:)

    Not enough info WAG 1-1.5uf Rob:)
  22. Replies
    694
    Views
    77,253

    Hello Valentin Up against 208's! That should...

    Hello Valentin

    Up against 208's! That should be an interesting comparison.

    Rob:)
  23. Replies
    21
    Views
    18,421

    Sticky: Here are the port dimensions Rob:)

    Here are the port dimensions

    Rob:)
  24. Replies
    7
    Views
    287

    No it will work just fine painted. Rob:)

    No it will work just fine painted.

    Rob:)
  25. Replies
    46
    Views
    3,132

    Hello Dino So how's it going with the amp?? I...

    Hello Dino

    So how's it going with the amp?? I like the EMO amps and have 2 set-ups using them.

    Rob
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4