Search:

Type: Posts; User: Robh3606; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.68 seconds.

  1. Replies
    26
    Views
    502

    All we listen too on our systems is a...

    All we listen too on our systems is a reproduction. There is nothing real about any of it in the recording chain. All that matters is that you enjoy the experience. I thoroughly enjoy listening to my...
  2. Go here for a more realistic measurement. I use...

    Go here for a more realistic measurement. I use mine is .5 cubic ft and they play to 300hz just fine. I cross them over to E-145's and they sound great once you dial them in. Rob:) ...
  3. How about 300Hz or so?? ...

    How about 300Hz or so?? Rob:)
  4. Replies
    716
    Views
    89,022

    Hello Ivica How do you know what is from the...

    Hello Ivica

    How do you know what is from the horn or the driver?? The driver is designed to be used as an SR driver with DSP. Anyone have measrurements with the 2430 and say a 2447/2451/2452 on...
  5. Replies
    20
    Views
    1,005

    Hello cgregory4 When you switch to biamp mode...

    Hello cgregory4

    When you switch to biamp mode in the stock speaker the HF compensation for the horn stays in place. Look at the schematic
    ...
  6. If box volume is really an issue KIS and use a...

    If box volume is really an issue KIS and use a single. Everest and the 4435 are both 2 1/2 ways with both woofers used as a pair over a very limited bandwith. Dual woofers operating over the same...
  7. Well without knowing your cabinet size it is very...

    Well without knowing your cabinet size it is very difficult to even discuss the woofers. Different woofers work best in defined sizes and tuning. If you need good LF response in a compact design it's...
  8. What do you have in them now?? Al or Ti?? Are you...

    What do you have in them now?? Al or Ti?? Are you running them straight out or with a tweeter.

    I don't have the Truetent diaphragm's but have used and own all three materials in various drivers. I...
  9. Yes that is correct. Each crossover was set-up...

    Yes that is correct. Each crossover was set-up for each specific driver set. They are not interchangeable. You would have to get a measurements set on the GPA and try it in a crossover simulator.
    ...
  10. Replies
    22
    Views
    1,233

    What did the dealer have to say?? Did you let...

    What did the dealer have to say?? Did you let them know you had an issue??

    Rob
  11. Replies
    97
    Views
    7,680

    Glad you are enjoying them looking forward to...

    Glad you are enjoying them looking forward to your impressions.

    Rob:)
  12. Replies
    2
    Views
    246

    There is always some phase shift through a...

    There is always some phase shift through a crossover. It is aproximately 90 degrees per pole so an 18Db network will give you 270 degree's. Your best bet is to try it both ways to see which sounds...
  13. What versions of the 811 or 813 A,B or C?? They...

    What versions of the 811 or 813 A,B or C?? They may be very hard to find parts for so make sure they are in good shape before you pull the trigger. They are large format monitors so they don't...
  14. Replies
    716
    Views
    89,022

    Hello 4313B That was the plan so I could get...

    Hello 4313B

    That was the plan so I could get the offset closer to try to time align them.

    Rob
  15. Replies
    18
    Views
    1,200

    It's an underhung coil. You couldn't get better...

    It's an underhung coil. You couldn't get better heatsinking with the mass of the magnetic structure.
    What kind of power levels?? I run mine with 100 watts and it's more than enough and with those...
  16. Well if you are switching out the series inductor...

    Well if you are switching out the series inductor L1 of the crossover you are essentially running them full range. You need the DX-1 or another suitable active crossover to roll the woofer off...
  17. Replies
    97
    Views
    7,680

    Hello Don Can't wait to see how you like them...

    Hello Don

    Can't wait to see how you like them in your room and how flexible you find the DSP for the room EQ. Based on the DSP I have installed in a Crown XTI amp it should be quite impressive and...
  18. Replies
    716
    Views
    89,022

    I didn't source the horns. I wish! I have 2216's...

    I didn't source the horns. I wish! I have 2216's the PTH 1010's with 476Mg's. I was happy to get the box dimensions for the 2216's

    Rob
  19. Replies
    18
    Views
    1,200

    Or E-145's Rob:)

    Or E-145's

    Rob:)
  20. Replies
    716
    Views
    89,022

    Hello 4313B Thanks for posting that techsheet....

    Hello 4313B

    Thanks for posting that techsheet. Couldn't have been more timely. Just about ready to cut wood.

    Rob:)
  21. Hello Baron, Heather I have been using the PS...

    Hello Baron, Heather

    I have been using the PS series in my "big system" for years. I have PS-200's on the E-145's 2123's and 435Be's. I use a PS-400 on my pair of B380 clones. They sound better...
  22. Replies
    23
    Views
    1,969

    The midband response is what the sensitivity is...

    The midband response is what the sensitivity is based from and where you would match driver sensitivity. That graph is misleading. There is quite a difference in bass roll-off between the 2 drivers...
  23. Replies
    17
    Views
    1,160

    Hello Are you using the stock crossover?? The...

    Hello

    Are you using the stock crossover?? The main difference between the 4430/35 is the power handling down low. Tuning up at 40 hz is going to effect how the woofers sum in the first two...
  24. Replies
    38
    Views
    3,354

    With quitar pick-ups are they designed to be...

    With quitar pick-ups are they designed to be linear?? Sounds more like a MI speaker application and there are significant differences between magnetic vs VC differences in say an E-130 and a 2235 as...
  25. This is the driver line up in my 4 way active...

    This is the driver line up in my 4 way active mains. I have B380's 2235's with BX-63A up to 80Hz E-145's up to 300Hz to 2123's up to 1.5K to PTH1010's with 435Be's. Works quite well. I wouldn't get...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4