Search:

Type: Posts; User: kartsmart; Keyword(s):

Page 1 of 9 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    6
    Views
    548

    Thanks Grumpy, leads 1 and 2 on L pad = 40 ohms...

    Thanks Grumpy, leads 1 and 2 on L pad = 40 ohms fully clockwise 22 ohms at the 12 oclock position and 0 ohms fully counter clockwise , again thanks
  2. Replies
    6
    Views
    548

    3134 3130 network

    i have been searching the forum for the 4430 and 4535 hf crossover diagram schematic replacing the 30ohm rheostat replaced with the 8ohm L pad does anyone who where its at ?
  3. Replies
    6
    Views
    548

    good

    Thanks Rob that makes my day complete :D
  4. Replies
    6
    Views
    548

    is it a 2123H or J

    I bought awhile back what was to be a pair 2123H 8ohm but after looking closer the cone is maked 66287 . 66287 is the J ? i put a ohm meter on it and it reads 4.8 ohms across the leads ? what do i...
  5. Replies
    12
    Views
    2,419

    Posted by Tre'...

    Posted by Tre' (P) on October 5, 2013 at 17:00:22In Reply to: RE: YUP posted by Ed Schilling on October 5, 2013 at 09:34:08:


    "Well, I say "not in the signal path" because the Coil and cap are...
  6. Replies
    12
    Views
    2,419

    I swapped out the E-145 for TAD 1602 with good...

    I swapped out the E-145 for TAD 1602 with good results . so its tad 1602 2118 mid and the amt for the top i like what i here ,sounds promising . now i would love to get it all passive x-over any...
  7. Replies
    12
    Views
    2,419

    thanks Rob for your efforts and help / i'm in the...

    thanks Rob for your efforts and help / i'm in the process of putting on a high gloss black finish on cabinets now so it might be a little while again thanks
  8. Replies
    12
    Views
    2,419

    your the one its the original 4826 boxes same...

    your the one its the original 4826 boxes same cubic ft as for subs i got a pair of 2246 18" suds
  9. Replies
    12
    Views
    2,419

    yes your correct on the front panel but with the...

    yes your correct on the front panel but with the extra bracing i used and ports made out of 3/4' stock box volume should me very close to original / as for the software i no longer have excess to ....
  10. Replies
    12
    Views
    2,419

    4628B make over

    I'm finally getting back to this project. :applaud:i'm in the works of redoing 4628Bs the plan is E145-2118- ESS AMT-1A air motion transformer . the help I need for know is calculating the port...
  11. Thread: TAD Recone

    by kartsmart
    Replies
    3
    Views
    2,076

    TAD Recone

    I have 4 TAD 1602 drivers . I would like to recone them to 1601A or 1601B does anyone know if the baskets are interchangeable ? :dont-know:
  12. Replies
    56
    Views
    40,714

    How about a sketch of these wave-guides for us...

    How about a sketch of these wave-guides for us DIY guys
  13. Replies
    56
    Views
    40,714

    tpl-150h

    Just thinking /tpl-150h for replacing the 2404 in the 4628B and 2445s for low end ? :bouncy:
  14. Replies
    4
    Views
    1,836

    Grumpy thanks for the reply, I will be using...

    Grumpy thanks for the reply, I will be using these for music play back for home use . I have read in one of zilchs threads that the port tuning could be a little lower and the 8" mid could crossover...
  15. Replies
    4
    Views
    1,836

    up grading the 4628B

    I have a good pair of 4628b , it has a good pair of E-145s and good pair of 2218s , I have on hand a pair of 2435HPL or a pair of ESS amt 1a airmotion transformer , to replace the 2404 ,
    what...
  16. Replies
    83
    Views
    38,508

    I give up

    i give . please what is the answer :banghead:
  17. Replies
    83
    Views
    38,508

    not sure ?

    Im guessing + to black for 2123 2241 2404 ? :blink:
  18. Replies
    83
    Views
    38,508

    polarity question

    just would like to check - what would the the polarity connections be for the drivers / 2123H 2441 2405 / and biamped 2245
  19. Replies
    83
    Views
    38,508

    Thank You thank you

    Thanks for your time to answer my questions , hopefully i will get these done , I had one of the worst years of my life !!! once again Thanks !!! :D
  20. Replies
    83
    Views
    38,508

    Help

    I am finishing up my 3155 cc networks \ I have 2 questions \ 1 hooking up the Lpads does the terminal 3 go to crossover and terminal 2 go to the driver and terminal 1 go ground / as in the 4344 MK...
  21. Replies
    83
    Views
    38,508

    im back

    Been in hospital for the last 3 months looking forward to get back to this project when I'm able !
  22. Thread: DAC question

    by kartsmart
    Replies
    16
    Views
    9,546

    There seems to be some debate firewire VRs usb ,...

    There seems to be some debate firewire VRs usb , Not so much as in preformance but cost of cable's ,Firewire can use a cheep cable where usb will need a quality cable , Is this true ?
  23. Thread: DAC question

    by kartsmart
    Replies
    16
    Views
    9,546

    DAC question

    from what I have read Dac,s do not sound alike , soft, punchy , soundstage , narrow, wide ? for the equipment I have what would work good in the $ 1000-1500 range .


    I-mac for music...
  24. Replies
    83
    Views
    38,508

    Shipping ??

    Went to order part from solen everything seemed good until the shipping charges was applied, $163.00 can this be right ? :eek: E-mailed them but no reply. This will sure put this project over...
  25. Replies
    83
    Views
    38,508

    Just checking before ordering parts L4 470u...

    Just checking before ordering parts L4 470u is the same as .47mh ?
Results 1 to 25 of 214
Page 1 of 9 1 2 3 4