I've had good luck Charge Coupling bypassed electrolytics when the LF circuit needed large values that would have broken my bank.It occurs to me that one could also incorporate film caps in parallel...
Type: Posts; User: 4343; Keyword(s):
I've had good luck Charge Coupling bypassed electrolytics when the LF circuit needed large values that would have broken my bank.It occurs to me that one could also incorporate film caps in parallel...
https://www.ebay.com/itm/165704145150
Can't read the model number, but the label seems authentic to me for the Los Angeles era. It's old enough to have a genuine Cannon socket on it, and what...
Face down on thin carpet? Bump it a bit...
Mine had 4 ohm red woofers in them and those came right out. Finding the -3 woofers did take a while. I went with a pair of -2's while looking, they are...
Are the TruExtent Be diaphragms available in 16 ohms?
Personally, I would double the 2226J for 8 ohm bottom and use 8 ohm diaphragms from the start, but you have what you have...
Concerned? :dont-know: No, but be aware that the RCA-XLR adapters MUST be wired XLR pin 3 to RCA center pin or nothing passes through. If you can't open them to swap pins, don't buy them unless they...
Rick Cobb for foams.
[email protected]
Should not be any glue, but paint tends to stick together after 30 years...
Masking tape as described in the beginning of this thread.
On a related note, has anyone had any luck matching the color of the Heathkit green baskets and cones? I'd like to find a way to turn a...
Agree, but let's not forget the L110. The LE111 has a white woofer, it's just on the inside... Plus you could swap in a LE10 if you wanted the white on the outside, even update the mids and tweets to...
Just want to say +1 on the Carpenter's Wood Glue Max. It's the best I've used.
Oh, and for filling I use auto body filler. Currently sanding the 1" round-overs on some 1.25" particle board. The...
Maybe it was in such sad shape they were ashamed to put it on the curb!
As to the AlNiCo vs Ferrite, I use both, but try to keep them in pairs. The AlNiCo magnets ended up in a very small box with...
http://www.ebay.com/itm/JBL-LE-111A-SPEAKER-WOOFERS-FROM-PAIR-OF-JBL-L110-SPEAKERS-NEEDS-REPAIR-/272296020593?hash=item3f661b8a71:g:PbcAAOSwRQlXeg-y
Look kinda mistreated, but perhaps the shipping...
So you want to convert the horn crossover from a bandpass filter to a highpass filter. I'd start by shorting across the series .27uH inductor and removing the 2 3uF caps that drain the HF off and see...
Face down on carpet and raising a few inches and dropping it has worked for some. Or the putty knife slid under the edge of the basket. (Don't cut the O-Ring by going in too far.)
The tiny 10-32...
Look for the 4344MKII crossover. Use that, either as a starting point for further tweaks, or as is.
I built the 2123H BPF as it is shown (Something like 300-1.2KHz, IIRC) and it works great in...
My 2226J's are setup similar to your cabinet, vent in between. Vertical works best on mine. I used a big inductor on the bottom woofer to roll off the mids from it. I used 9mH on the 2226J's, for...
@PictureDisksMatter (somewhat more):bouncy:
^^^^ This.
Might try some tar remover from an auto store on that magnet.
Sounds like there might be some sort of foam rot gunk in the gap. If you don't know how to remove the cone and spider...
I've done both, the screws are used when I want to make something permanent, I leave them off for experiments. One (unfinished) experiment even has a few panels that were edge glued because they were...
Stunned.:eek:
Falls right in line with the 2 x 3" ports 5.75" long that Bass Box 6 gives.
Do consider the flared ports.
Don't have a 4646A, but I just happened to have Bass Box 6 Pro open running the numbers on my 4648. (Have a pair of 2234H's and an empty box...)
It says that a 2206H in 1.2 cu. ft. would like 2 ...
Couldn't agree more.
Usually there is a hard gasket stuck to the face of the drivers. Usually gray. Not hard to make some out of a thin (1/16" or so) card stock or cork sheet. No glue or silicone...
JBL may have wanted the box to be an "outie" so that they would not have some versions of the same line being opposite. Thus the switch of the woofer wires colors. The first schematic has the wires...
Are you talking about a protection cap for bi-amping, or an actual crossover cap for passive listening? The protection cap needs to be an octave below the crossover frequency so as not to interfere...