Search:

Many thanks for the advice. Sure wish I had started this project a few years ago :blink: $$$$!

Greetings All,

Tried doing some looking throughout the forum for an answer on this question but...

Getting ready to start a 4350/4355 build. Curious what the thoughts are on using Baltic birch...

Widget-

Have not tried running a signal into them. More than anything just curious what one would/could do with them.

Thanks for the info.

Greetings-

I have two 375 16ohm drivers and one measures 9.2 ohms while the other measures 22.3. What causes such a discrepancy in the measurements?

Thanks
Chris

I have a choice of 2- 2235's or 2- k151's.

Running klipsch la-scalas and want to pick up where the klipsch drop off in the low end and provide some additional LOW end.

What would be your...

Condition isn't a concern, as long as they work properly. My wallet doesn't want to open up too wide... how much should I expect to spend?

And thanks for the offer Woody. Your'e a 100 miles from...

How hard is it to come by the 2441, 2311 and 2308 portions of the 4355 monitor?
I have the rest of the drivers in boxes. Looks like it would be a fun speaker to build...

Its either another...

Thanks- I will do some homework on the subject.

Regarding the software- I think it would be interesting to try and clean up some old LP's and reel to reels.

Also, the reason for a dedicated...

Too many 7-1/2", cassettes and some LP's-

Anyone have thoughts on how to put together a dedicated PC to transfer old reel to reel tapes,cassette tapes etc...? What hardware, software and...

Ian- If I had more time I would love to build the wooden horns, they look gorgeous...

Moving Along...
Every driver I listed has a mate (pairs) I also have a pair of K-151's to throw in.
...

Thanks for the suggestion...I have already built 4430 clones and am getting used to them. However the butt cheeks ran me over $300 and the external X-over was $250. I think I was lucky finding those...

Looking for some advise...

I am wanting to build a pair of speakers and use up some of my collection of JBL supplies that are collecting dust.

I would appreciate the forums thoughts on what...

Nice Pix-

I will be more specific. I would like to run the 2405 off the same amp as the horns but take them up to around 8000hrz. I am running the 4430's with an external crossover. What do I...

First off- Thank you to the forum members for the advise and guidance on building my first pair of 4430's! :applaud:

Sooooo...the modifications now begin. I would like to add a pair if 2405's to...

Anyone suggest a good shop in Portland, Or. to have a couple of 2235 surrounds redone?

Called a few and got quotes from $30-110.00

Thanks

Zilch- "The ones I built, or the real deal"?

What's the difference? Widget had mentioned something about charged couple?

Not sure where to post this?

Where can I find the correct crossovers for the 4430?

I have started to follow a couple of threads in the "search" and my head is about to explode!

Any...

It's done... I hope I dun it rite?:nutz:

Anybody know what the cut out for the high freq. driver should be for the 4430? I am after the actual opening not the horn pad.

The threads containing the hoffman measurements did not include...

Whew!
Thanks speakerdave.

Now, who do I talk to around here for a crossover for the 4430's :D

As I am totally in the middle of glue and slivers I started to build the driver supports for the high freq. Holy crap:blink:, I have 2426h's not 2425h's.
Can I use 2426's for the 4430 monitors?

I am not wanting to mix drivers. I need a little guidance as to what the speaker compliment should be. 4430 + xxx5, or a 4430 and 2235 sub. The more I am looking into this the 4430 + 2235 sub might...

I am basically building a 4435, but split into two boxes. I would like to use the crossover network from a 4435, bi-amped of course. I do not have the networks as of yet.

I need to travel into...

I am building the 4430's and separate boxes for the bass. How many port holes do I need to drill for the bass boxes using 2235's? I noticed on the 4435's that there is only one port. Is this because...

Right in the middle of the project and cannot determine from the hoffman drawings what the correct opening for the 2426 driver should be. From the jbl site the driver measures 5-7/8. Does anyone have...