Search:

Type: Posts; User: short_circutz2; Keyword(s):

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    894

    Mine are powered with a Sherwood S9910 (rated at...

    Mine are powered with a Sherwood S9910 (rated at 100w/ch into 8 ohms, but closer to 120w/ch) which is more than adequate power for them. The L65 has pretty good sensitivity and in my case, the...
  2. I dont understand why you're trying to install a...

    I dont understand why you're trying to install a recone kit for a 12" speaker into a 15" frame...
  3. Replies
    7
    Views
    1,434

    😂

    😂
  4. Replies
    29
    Views
    6,830

    Thanks for the clarification 😁

    Thanks for the clarification 😁
  5. Replies
    2
    Views
    958

    Pretty sure Edgewound makes a very close repo kit...

    Pretty sure Edgewound makes a very close repo kit for 2234/5.
  6. Replies
    29
    Views
    6,830

    The EVM-18B was used in the SH1810L-ER bass cab,...

    The EVM-18B was used in the SH1810L-ER bass cab, a "SubScoop" design. It has useable response to -10dB at about 34 hz. I have a pair of the mid/hi cabs that were part of this system.

    ...
  7. Photo of the other side of this would be helpful

    Photo of the other side of this would be helpful
  8. Replies
    15
    Views
    3,722

    How about the bass section from the 5742 cinema...

    How about the bass section from the 5742 cinema system? cab? Its designed for dual 2242...25Hz at -10dB, 30Hz at -3dB

    https://jblpro.com/en/products/5742

    Edited to add...oops, I see there was...
  9. Replies
    27
    Views
    5,449

    Depending on when the cabinets were manufactured,...

    Depending on when the cabinets were manufactured, the top panel comes off where a 2345 or 2370 horn bolts right in. The 2370 is a hair too big to fit in the opening of the older cabinet version.
    ...
  10. Replies
    16
    Views
    8,071

    I inherited my late father's S-9910 and his L65...

    I inherited my late father's S-9910 and his L65 speakers. Match made in heaven. That receiver puts out closer to 120 w into 8 ohms. It's a very under appreciated and under rated receiver
  11. Replies
    199
    Views
    175,077

    Don't forget the muffler bearings and blinker...

    Don't forget the muffler bearings and blinker fluid. You'll need a left handed monkey wrench to add these vital items.
  12. Replies
    22
    Views
    10,977

    My father and I have normally just covered the...

    My father and I have normally just covered the fiberglass batting with window screen.
  13. Replies
    9
    Views
    4,538

    Also, keep in mind, the reason an l-pad is used...

    Also, keep in mind, the reason an l-pad is used is to keep a constant impedance across the output of the passive crossover the same throughout any adjustments so that the crossover frequency isn't ...
  14. Replies
    22
    Views
    24,641

    Strange...the LE14a that are in my L99 have the...

    Strange...the LE14a that are in my L99 have the aquaplas on the front of the cones.
  15. Replies
    14
    Views
    4,249

    For non-JBL and non-Altec items, discussion might...

    For non-JBL and non-Altec items, discussion might be more appropriate here:

    http://www.audioheritage.org/vbulletin/forumdisplay.php?6-General-Audio-Discussion
  16. Replies
    26
    Views
    16,236

    Beat me to it.

    Beat me to it.
  17. Replies
    26
    Views
    16,236

    Because that's what you were either expecting or...

    Because that's what you were either expecting or thinking. With bi- wiring, if a distorted signal is going through one set of cables, the SAME THING is going through the other set going to the same...
  18. Replies
    1
    Views
    1,269

    No. That M112 is, in a nutshell, a crappy, ...

    No.

    That M112 is, in a nutshell, a crappy, cheap, pressed steel frame speaker used in bottom of the pile PA cabs such as JRX, TR, MPro 200 series, etc. And not a good sounding 12 at all.

    I...
  19. I have a pair of the same cabs. Seeing as my...

    I have a pair of the same cabs.

    Seeing as my SR4731X arent in use and buried in the back of my storage unit, I had pulled the woofers out of them, so now the JRX cabs have 2206H woofers in them. ...
  20. Replies
    34
    Views
    16,039

    I've normally just covered the fiberglass...

    I've normally just covered the fiberglass insulation using fiberglass window screen to avoid stray fibres
  21. Replies
    115
    Views
    53,924

    So, are the motors 128H or 129H? According to the...

    So, are the motors 128H or 129H? According to the "goes into" doc, recone kits for the 128H and 129H arent interchangeable!
  22. Replies
    115
    Views
    53,924

    So, your 128H drivers were reconed with 129H...

    So, your 128H drivers were reconed with 129H kits?

    According to the "goes into" pdf at...
  23. Replies
    97
    Views
    72,221

    Dad was a JBL fanatic since the 60s. He used them...

    Dad was a JBL fanatic since the 60s. He used them exclusively for his MI cabs for both guitar and bass. First experience I had with JBL was when dad bought his first real home system JBL L65, powered...
  24. Replies
    8
    Views
    6,967

    MyTL3512 subs have DL18W woofers. They originally...

    MyTL3512 subs have DL18W woofers. They originally had "EV" on the dust caps, shown also in the literature for this subwoofer model.
  25. Did ANYONE even look at the JBL Proservice pdf I...

    Did ANYONE even look at the JBL Proservice pdf I linked? The answer is plain as day on the wiring diagram on it!
Results 1 to 25 of 47
Page 1 of 2 1 2