Search:

Type: Posts; User: Robh3606; Keyword(s):

Page 1 of 3 1 2 3

Search: Search took 0.03 seconds.

  1. Replies
    165
    Views
    144,560

    I don't think that's going to work. As a minimum...

    I don't think that's going to work. As a minimum a different driver on the M2 is going to give you a different impendence plot. Take a look at this thread where I have 8 ohm 2453-SL's on the PTH1010....
  2. Replies
    165
    Views
    144,560

    Hello Rusty It's a weird shaped room with a...

    Hello Rusty

    It's a weird shaped room with a large walk in closet filling one corner. One speaker is close but better the other has no wall close. There is no way to get symmetry with placement...
  3. Replies
    165
    Views
    144,560

    Hello Widget Yes it was literally staring me...

    Hello Widget

    Yes it was literally staring me right in the face. The key was a simple phase test. I had been running my Heil's in the room that way and just dropped these right into basically the...
  4. Replies
    165
    Views
    144,560

    I was doing some comparisons with with my...

    I was doing some comparisons with with my basement system and these and I just couldn't match the sense of space I was getting from the PTH1010/2453SL and these speakers. After thinking about it...
  5. Replies
    165
    Views
    144,560

    My passive speaker is not time aligned and in my...

    My passive speaker is not time aligned and in my case the compression drivers leads. Not worried about the time alignment. As long the summation is good through the crossover region all is well.
    ...
  6. Replies
    165
    Views
    144,560

    Hello Thanks! They use a 270us delay to...

    Hello

    Thanks!

    They use a 270us delay to time align them using the DSP for the M2. So no they don't align you would have to push back the horn a bit but then you introduce another set of...
  7. Replies
    165
    Views
    144,560

    Thanks Guys! Rob:)

    Thanks Guys!

    Rob:)
  8. Replies
    165
    Views
    144,560

    Thanks! I had them dialed in before I...

    Thanks!

    I had them dialed in before I finished the cabinets although I haven't powered them up yet so I don't know how lossy my cabinets were using just a couple of screws. Also hopping I don't...
  9. Replies
    165
    Views
    144,560

    One done one to go! Rob:)

    One done one to go!

    Rob:)
  10. Replies
    165
    Views
    144,560

    Well got a top finished and a bass veneered seem...

    Well got a top finished and a bass veneered seem to match up well. Have to formica the bass cabinet top and bottom. Now for some lesson's learned.

    I got 10mil backed veneer with psa? glue which is...
  11. Replies
    165
    Views
    144,560

    Thanks Widget! Rob:)

    Thanks Widget!

    Rob:)
  12. Replies
    165
    Views
    144,560

    Thanks Chris Rob:)

    Thanks Chris

    Rob:)
  13. Replies
    165
    Views
    144,560

    Sanding filing and filling! Beautiful weather...

    Sanding filing and filling! Beautiful weather today! Getting a lot done both tops ready for sealing. Working on the bottoms. Have a flat black eggshell coming tomorrow for the backs and any exposed...
  14. Replies
    165
    Views
    144,560

    It's been rain, rain and more rain. Wish I could...

    It's been rain, rain and more rain. Wish I could send some of it west. Just finished getting my second top routed and ready for veneer and formica. Doing walnut first then doing formica tops to...
  15. Replies
    165
    Views
    144,560

    Hello Widget Now I went and did it got a 4x8...

    Hello Widget

    Now I went and did it got a 4x8 sheet of 10 mil flat cut paper backed walnut vernier that is pre-coated with adhesive so peel and stick. Getting 4x8 of flat black formica for top and...
  16. Replies
    165
    Views
    144,560

    Hello Widget Yeah it's getting close on the...

    Hello Widget

    Yeah it's getting close on the veneer. Don't want to break them down but I should just bite the bullet and get it done. Never done it before so it will be a learning experience. What...
  17. Replies
    165
    Views
    144,560

    Been just listening. I have updated my system to...

    Been just listening. I have updated my system to include a refurbished Emotiva XMC-1 to use as my preamp in a stereo system. All of my sources are digital and I was looking for something that had...
  18. Replies
    165
    Views
    144,560

    It took weeks but I finally got my 1.8M resistors...

    It took weeks but I finally got my 1.8M resistors so I could charge couple the networks. Got them finished and they sound great! Now it's just the cabinets! Just did a verification to see if the...
  19. Replies
    165
    Views
    144,560

    Been listening and having fun. Added an Impedance...

    Been listening and having fun. Added an Impedance conjugate to tame a peak, and minimize phase angle to +/- 30 degrees. Retired the PS-200 and am using a pair of Emotiva HC-1's running with balanced...
  20. Replies
    165
    Views
    144,560

    Hello Pos Thanks!! On the 2453SL no I actually...

    Hello Pos

    Thanks!! On the 2453SL no I actually don't have any 2450's the 476's would be the only valid comparison I have. The 2453's are going downstairs in my active set-up only going to use them...
  21. Replies
    165
    Views
    144,560

    Thanks guys!! It's a rainy day here and I...

    Thanks guys!!

    It's a rainy day here and I have off so have been listening to them. I am really impressed just how dynamic they are. I have been doing a shoot out between my basement system and...
  22. Replies
    165
    Views
    144,560

    Well it's great when a plan comes together and it...

    Well it's great when a plan comes together and it all works out. The decision to build the cabinets low tuned with a bump filter is working out very well. I get the last octave fill with no boom at...
  23. Replies
    165
    Views
    144,560

    OK back to the build! So I got the passive...

    OK back to the build! So I got the passive crossovers done and installed. When I was doing the biamp passive comp on the CD it sounded really good on some material and not quite right with others. I...
  24. Replies
    165
    Views
    144,560

    Thanks Widget!! I found them on the site!! For...

    Thanks Widget!!

    I found them on the site!! For next time!! I have one PCB built and tested and it's good! Was really worried about keeping the level right for a max flat response. Did a quick...
  25. Replies
    165
    Views
    144,560

    And the fun begins!! Got my crossover components...

    And the fun begins!! Got my crossover components so I can see if the network is right. The caps in the high pass are going to be charge coupled so large values x 2 takes up a lot of space. Wish I...
Results 1 to 25 of 74
Page 1 of 3 1 2 3