Search:

Type: Posts; User: Robh3606; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 2.45 seconds.

  1. Replies
    156
    Views
    42,545

    My passive speaker is not time aligned and in my...

    My passive speaker is not time aligned and in my case the compression drivers leads so you would delay it not the woofer. Not worried about the time alignment. As long the summation is good through...
  2. You don't need money this is a free box program...

    You don't need money this is a free box program that come preloaded with lots of drivers. You can also enter new ones. It has the 2235 and Le15 preloaded not sure if you can do the passive radiator....
  3. I don't go through a lot of gear I tend to like...

    I don't go through a lot of gear I tend to like and keep. I have either Crowns or Emotiva in all my systems. My HT is a mix of Crown and Emotiva. I have Crowns on the 4 way active stereo mains and...
  4. Hello BMWCCA Yes I can only think of one time...

    Hello BMWCCA

    Yes I can only think of one time I could get those comparator lights to flash on any of them. My PS400 was driving stereo subs and I was seriously pushing the limits in my HT on a...
  5. Replies
    156
    Views
    42,545

    Hello Thanks! They use a 270us delay to...

    Hello

    Thanks!

    They use a 270us delay to time align them using the DSP for the M2. So no they don't align you would have to push back the horn a bit but then you introduce another set of...
  6. Good luck with that I doubt you are going to find...

    Good luck with that I doubt you are going to find 4 PS-400. I have 1 PS400 and 6 PS 200 in service. The PS 400 and 3 PS 200 in my HT and 3 in a bi-amp set-up. Had most of them checked out after I...
  7. You are going to have to run them in a box...

    You are going to have to run them in a box program to see which is best in the box size you can live with.

    Rob :)
  8. I tried aftermarkets years ago and the...

    I tried aftermarkets years ago and the measurements were all over the place. Even if those were good you would still need the dampening pads that go under them. I would look elsewhere.

    Rob:)
  9. The only carver gear I have ever owned was the...

    The only carver gear I have ever owned was the Phase 4000 preamp. I loved it but it died. On the amp front when I had my XPL's and DX-1 running I used crown amps with them and never had an issue with...
  10. Replies
    125
    Views
    27,486

    Hello Toddalin I missed this. OK why not have...

    Hello Toddalin

    I missed this. OK why not have to wait till I get them up and running again. They have been temporally "retired" I didn't realize that they used a 60 degree angle on the "wings"....
  11. Hello Barry Does it have a deeper frame and...

    Hello Barry

    Does it have a deeper frame and cone like say an E-145 with the extender ring vs standard frame?? Deeper cone also like an E-145?? Is it a supped up E-145 power wise??

    I have never...
  12. Replies
    43
    Views
    2,089

    They must be changing the throat diameters on the...

    They must be changing the throat diameters on the Radians to 1.5" They are 1.4" and 2" available for stock drivers. Unless they drop a sleeve into the horns throats can't imagine them redoing the...
  13. Yes they do and legacy is so important done at...

    Yes they do and legacy is so important done at 10:09:10

    Rob:)
  14. Replies
    10
    Views
    767

    They are supposed to be interchangeable main...

    They are supposed to be interchangeable main differences is power handling. Curious to see what you find, I have used 2035's and found them to be good drivers.

    Rob:)
  15. Replies
    10
    Views
    767

    See what happens when you add a sub! Think it's...

    See what happens when you add a sub! Think it's good now just wait!

    Rob:)
  16. Replies
    42
    Views
    2,952

    Please don't take a nice pair of vintage speakers...

    Please don't take a nice pair of vintage speakers and butcher them. Leave them be and make new cabinets.

    Rob:)
  17. Replies
    4
    Views
    318

    You would have to change to a HL 93 2392 2"...

    You would have to change to a HL 93 2392 2" throat horn. Physical fit?? Probably. Might work out well. The horn in the stock 4333 is quite long.

    Rob:)
  18. This will get you started ...

    This will get you started

    http://www.audioheritage.org/vbulletin/showthread.php?29391-Hiraga-s-crossover-for-Altec-A5x


    Welcome!

    Rob:)
  19. Replies
    43
    Views
    2,089

    Hello Earl Great thanks for posting them. That...

    Hello Earl

    Great thanks for posting them. That gives us a more complete picture of what to expect.

    Rob:)
  20. Replies
    6
    Views
    635

    They look great! Lucky to find a pair in such...

    They look great! Lucky to find a pair in such good condition.

    Rob:)
  21. Replies
    43
    Views
    2,089

    Found the Truextent measurements pos did them in...

    Found the Truextent measurements pos did them in a 2450SL core you can see the roll off. Similar to the 476Be

    ...
  22. Replies
    43
    Views
    2,089

    Hello Grumpy The 476Mg runs out past 20K on...

    Hello Grumpy

    The 476Mg runs out past 20K on the M2 waveguide and is clean on a CSD. It doesn't have the all the "noise" from the secondary resonances that the Ti diaphragm's have. The Be are also...
  23. Replies
    43
    Views
    2,089

    Here is a brand new DR82450SL and mine looks...

    Here is a brand new DR82450SL and mine looks almost the same. You have to remember that you are dealing with a flat ribbon that gets twisted from the opposite side and gets twisted again to make a...
  24. Replies
    43
    Views
    2,089

    What you have in the white paper is the DCR not...

    What you have in the white paper is the DCR not the same. In general Impedance is about 2X the DCR value. Take a look at the 2452SL techsheet H vs J. What you need are 16 ohm SL or coated...
  25. Replies
    43
    Views
    2,089

    What's wrong?? Are you having a corrosion issue??...

    What's wrong?? Are you having a corrosion issue?? That was reported on this forum a while back. You should be able to fit the 2450 family diaphragms in the 476 Core.


    The 476 Mg are 16 ohm...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4