Search:

Type: Posts; User: LHorn; Keyword(s):

Search: Search took 0.01 seconds.

  1. No expert here but a spinning screw is a likely...

    No expert here but a spinning screw is a likely suspect. You dont need to take the crossover out to check that...just pinch the 6 white pegs holding the top circuit board on and raise it up...see...
  2. Replies
    0
    Views
    299

    JBL Ti series grille peg info needed

    Does anyone have a 240Ti or 250Ti grille peg off their grille to get me an accurate dimension? I know the 120Ti is a ball type peg and 18Ti is the same except the 18 is molded into the grille itself....
  3. Replies
    14
    Views
    1,690

    I painted it on Jan 20th...and it is very quick...

    I painted it on Jan 20th...and it is very quick drying..like 10 minutes. On my test piece of aluminum I have to really try hard to scrape it with a fingernail. I dont think it is as hard as the...
  4. Replies
    40
    Views
    24,791

    I see...I figured there had to be some way to...

    I see...I figured there had to be some way to align the vc since it cant be shimmed. To be sure I have this right...I do have a 10k uF cap..same thing right?

    Thanks DavidF.
  5. Replies
    40
    Views
    24,791

    After looking at that pic again...I'm not sure I...

    After looking at that pic again...I'm not sure I got it yet. The tapered head of the screws cant reach that far down to center the plinth can it...it will only center the top plate?

    So lets say...
  6. Replies
    14
    Views
    1,690

    Thank you...and yes I went with Amazon.

    Thank you...and yes I went with Amazon.
  7. Replies
    14
    Views
    1,690

    Thanks for the tips badman and Michael Chavez. ...

    Thanks for the tips badman and Michael Chavez.

    I finally got around to painting this driver. The paint Mr. Widget recommended is spot on..thank you for that. Freshly done it doesn't look exactly...
  8. Replies
    40
    Views
    24,791

    I see...so the tapered screw heads are actually...

    I see...so the tapered screw heads are actually doing the centering. That is the part I couldn't grasp knowing there is always some play with anything that a screw or bolt goes through. I would have...
  9. Replies
    14
    Views
    1,690

    I found it on Amazon too..has the same Part...

    I found it on Amazon too..has the same Part Number K01613A07 as the Grainger's link you gave...
  10. Replies
    14
    Views
    1,690

    That sounds right..I knew it wasn't flat and...

    That sounds right..I knew it wasn't flat and definitely not gloss..so satin was all I could think of. Semi-flat makes sense. Yes I always practice on something to get used to the way the spray...
  11. Replies
    14
    Views
    1,690

    Yeah I understand I wont get exactly the same...

    Yeah I understand I wont get exactly the same thing JBL used...just wondering if anyone has found a very good substitute. This is where I'm talking about..basically the area you see when the woofer...
  12. Replies
    14
    Views
    1,690

    Speaker Basket Refinishing?

    I need to restore the outside face and edges of my LE14H-1's. Is there a known paint that matches the original? From what I can tell its like a satin black type paint. I would like to get something...
  13. Replies
    40
    Views
    24,791

    Hello everyone..I realize this is an old thread...

    Hello everyone..I realize this is an old thread but there's one thing I cant grasp on this procedure. On reassembly..how do you get the voice coil centered? I have done LE14H-1's no problem..but I...
Results 1 to 13 of 13