Crossover for: 2405h & 2440 & E-145

Hey,


I´m nearly finished with building the bass-enclosure and know I´m thinking about the crossovers.

As I haven´t much experience building crossovers, I`d like to stick to established designs.
Are there any original crossovers shematics that would suit my system ?

My setup:
2405h
2440 on 2397 horn
E-145 in 7,5 cubic feet bassreflex

I´d like to bi-amp my system.
So one crossover for the E-145(probably just a coil!?) and one for the high-mid....
I don´t want any level controls, probably just a fix resistor for the midrange to compensate the higher efficieny over the tweeter.


Thanks a lot for your help,
Olaf

This is 2015 and you will probably find less expensive to get a digital crossover. That will allow you to better tailor the sound to you taste. Building a quality analog crossover is expensive and requires back and forth.

If biamping, and you wanted to keep it simple, you -could- run the
2397/2440 down to 800Hz-1KHz using an 24 dB/oct electronic
crossover (or 18dB/oct and a cap), let the 2397 run free on up,
and bring the 2405 in with a capacitor to come in ~9+KHz.

... or 100 other ways to do it.

And yes, you'll likely need to pad the horn drivers down.

Probably want to keep these away from side walls (or cut reflections down)
as the 15" driver isn't going to match the dispersion of the 2397 near
the crossover region.

You may further need to EQ the whole thing and figure out the best
component values to use for the pads and high pass capacitor, perhaps
adding an inductor to the HF section to clean up the MF/HF overlap
if it bothers you.

It's going to be a bit of work and 'back and forth' regardless, but
I hope you have fun in the process :)

Thanks both of you.


I know a DSP is a modern and "easy" way... But I was thinking about a passive crossover.

Is there such a passiv crossover, that suits the 2440 on the 2397 horn with the 2405h on top and the E-145 at the bottom ?

Quote:

---

Originally Posted by Dr.db

Thanks both of you.


I know a DSP is a modern and "easy" way... But I was thinking about a passive crossover.

Is there such a passiv crossover, that suits the 2440 on the 2397 horn with the 2405h on top and the E-145 at the bottom ?

---

And you also mentionned this :

Quote:

---

Originally Posted by Dr.db

As I haven´t much experience building crossovers, I`d like to stick to established designs.

---

No experience building crossovers on a non-existing configuration. There is no "establish design" for your non-stock configuration. The most logical direction is indeed to use a digital crossover to make some testing. Then if you are satisfied with the results, then try applying them with a passive crossover.

Sure, you can use any software that will calculate a basic crossover, But it doesn't mean it will sound good. There is more than crossing frequencies in a crossover.

BTW Click here for a long list of crossovers and their schematics. Then check what approximates your system.
http://www.jblproservice.com/navigat...chematics.html

Thanks a lot for the link :)

I know I´ve a none existing set-up.
But maybe a combination of the 3106 and 3110 could suit my speakers.

http://www.jblproservice.com/pdf/Net...%20Network.pdf

http://www.jblproservice.com/pdf/Net...%20Network.pdf


It would look like this:

2405:1,5mF + 0,3mH for Highpass 8khz

2440:9mF + 2,14mH for Highpass 800hz :confused:
0,3mH + 1,5mF for Lowpass 8khz

E-145:3,33mH +12mF for 800hz Lowpass :confused:

I´m not shure about the 800hz Highpass and Lowpass, anyone has an idea ?

Doctor,

Here are schematics of the crossovers I use with my E145/2447 combo.

george

Attachment 65835

Attachment 65836

Thanks george, very kind of you :)