PDA

View Full Version : 240ti crossover



Jerry
02-11-2010, 09:00 AM
I have a pair of 240ti's and have recently put into my system and noticed a difference in sound quality coming from each speaker. Traded sides and the sound was the same but now on opposite sides. changed amps, wires, nothing helped. One has a much bolder brighter sound. To make a much longer story shorter I have found a difference in the crossover. I was wondering if there was different boards installed over time as these don't have matching ser#. If not is there any photos here I can use as ref. to determine if one has been modified, can post photos of these boards if needed.

Thanks Jerry

rdgrimes
02-11-2010, 09:05 AM
Also possible you have a defective driver.

rdgrimes
02-11-2010, 01:35 PM
http://manuals.harman.com/JBL/HOM/Technical%20Sheet/240Ti%20ts.pdf

You'll find a small XO schematic on that tech sheet. Any competent technician can check out the XO for you with that schematic.

But I vote for a cooked driver, either mid or tweet.

Jerry
02-11-2010, 02:51 PM
http://manuals.harman.com/JBL/HOM/Technical%20Sheet/240Ti%20ts.pdf

You'll find a small XO schematic on that tech sheet. Any competent technician can check out the XO for you with that schematic.

But I vote for a cooked driver, either mid or tweet.


they may not be up to par but all are working. the crossovers in the cabs are different I will post a photo of each if I can so all can see what I am working with.

Thanks Jerry

Jerry
02-11-2010, 03:07 PM
http://picasaweb.google.com/jr35mm/240tiCrossover?feat=directlinkhttp://picasaweb.google.com/jr35mm/240tiCrossover?feat=directlink Tried to paste a link to gmail photo so the difference can be seen maybe someone can tell which one is the correct board config.

http://picasaweb.google.com/jr35mm/240tiCrossover?feat=directlink

Earl K
02-11-2010, 03:17 PM
Tried to paste a link to gmail photo so the difference can be seen maybe someone can tell which one is the correct board config.


><

Here ya go ,

http://lh3.ggpht.com/_7_fEPKDMy0o/S3R9i0p3QBI/AAAAAAAAHi8/6JECZujPjFU/s720/speaker-002.jpg
http://lh6.ggpht.com/_7_fEPKDMy0o/S3R9kA7lSRI/AAAAAAAAHjA/Rg2I6yEUCuk/s720/speaker-007.jpg

Jerry
02-11-2010, 03:57 PM
:banghead:

http://lh3.ggpht.com/_7_fEPKDMy0o/S3R9i0p3QBI/AAAAAAAAHi8/6JECZujPjFU/s720/speaker-002.jpg
http://lh6.ggpht.com/_7_fEPKDMy0o/S3R9kA7lSRI/AAAAAAAAHjA/Rg2I6yEUCuk/s720/speaker-007.jpg[/quote]
Thank you very much. As you can see I have two different configurations. may not be all the problem but has to be part of the problem, looks like a bit of mod went on here. :banghead:

Earl K
02-11-2010, 04:04 PM
Thank you very much.
You're welcome .


As you can see I have two different configurations. may not be all the problem but has to be part of the problem, looks like a bit of mod went on here .

- When capacitors ( the long cylindrical devices pictured ) are wired up in parallel with each other , the final value is the sum of the individual values .

- What's important is the final ( summed ) value .

- Add up the values of the caps that are wired together in parallel / compare that value to the cap(s) in the same ( position ) of the other crossover / and then report back to us your findings .


>< cheers

Don C
02-12-2010, 10:51 PM
Here is a picture of mine. I don't own these speakers anymore.