Crown XTI1000 bridged or Crown XLS602D stereo

[[email protected]]

http://www.crownaudio.com/amp_htm/xti.htm

Bridge-Mono, 8 ohms - 1000 watts

vs

http://www.crownaudio.com/amp_htm/xls.htm

Stereo, 8 ohms (per ch.) - 380 watts (760 watts total)

Which would be better as a subwoofer amplifier? Reliability, quality, etc?

[jerry_rig]

I have been using an XTi 2000 for the past two years or so as a PA amplifier and I have used it bridged for a bass guitar system. The XTi is a level above the XLS models, but I doubt most users have any use for all the bells and whistles (digital signal processing) built into these models. From my experience, it would make a dandy subwoofer amp, assuming you could put it in a separate room. The fans on all of these pro amps will drive you bonkers in a home setting.

[timc]

The XTi-1000 does not sound very good when bridged. It looses the impression of total bass controll that you get in Stereo mode.


I have not auditioned the XLS.


-Tim

[robertbartsch]

I have a few XLS amps. Theses are solid performers but the fans are loud as hell.

[[email protected]]

I just might go with the XTI 1000 in stereo then. 275 watts per channel seems sufficient for what I'm doing. Don't plan on killing my hearing entirely. Maybe around 80-90 dB, and maybe the ability to go to 100 dB. Listening distance would be 10 to 14 feet at most.

The XLS seems decent, but I'm reading of quality control issues with them. From what I gathered, the XTI line is made in the United States, so hopefully quality will be on a better scale.

Thanks all for your help. If you have anything to add, feel free to do so.

[hmolwitz]

For home use I would avoid amps with fans, there is a boatload of good amps without fans. The beauty of those new Crowns is when you need to load them up at the end of the job, and put them away.
Crown XTI: 18.5 lb (8.4 kg), 21.5 lb (9.8 kg)
Bose 1801 (Similar power rating) 82lbs

Harry

[Triumph Don]

K1 @ 350 per side or K2 @ 500 per side are great amps, run cool with no fans!


http://www.crownaudio.com/pdf/legacy/136713.pdf

[[email protected]]

Okay, finally gathered everything up. It's been a while, but I think I'm ready for this purchase.

Crown XTI1000 Digital Power Amplifier
http://www.amazon.com/exec/obidos/tg/detail/-/B000FFGFVS/ref=ord_cart_shr?_encoding=UTF8&m=ATVPDKIKX0DER&v=glance

Hosa 3' 3 Pin XLR Male to RCA Male Audio Interconnect Cable
http://www.amazon.com/exec/obidos/tg/detail/-/B0010CFML4/ref=ord_cart_shr?_encoding=UTF8&m=A17MC6HOH9AVE6&v=glance

Pyramid RSW1250 12 Gauge 50 Feet Spool of High Quality Speaker Zip Wire
http://www.amazon.com/exec/obidos/tg/detail/-/B000CQGMP4/ref=ord_cart_shr?_encoding=UTF8&m=API0ESPAS70OH&v=glance

Like I mentioned above, this would be a sub amp. Hoping to connect it using the sub outputs from the receiver. Once everything is dialed in, I'll use the XTI's internal DSP to configure the crossovers. Crossing my fingers at this point.

I'd appreciate if anyone could check whether this all works or not. Open to all suggestions.

Thanks.

[JBL 4645]

I have a few XLS amps. Theses are solid performers but the fans are loud as hell.

This why cinemas keep all-noisy amplifiers located in the booth isolated away from the auditorium.

They’d be better off located in different room with cables going though the wall from AVR/AVP that is in the listening room. Pass the speaker lead though the hole into the room and to the loudspeakers! Hence you won’t hear a bloody damn thing with all-those nosiy fans at all.:)

And it doesn’t matter if there whisper soft quiet fans. You keep adding the same amp the SPL dB will double up on all-the-amps then it will sound like one amp with one fan running at normal speed or what ever! Point is you don’t want to hear them! Only the recoded soundtrack, now then!