PDA

View Full Version : L100 Century polarity



B. Schafer
05-13-2003, 05:38 PM
My father has given me a lovely pair of L100's circa 1972. The speakers are aligned in a vertical array. I would guess that the black is + and the red is - on this speaker, since it is a JBL of this vintage. Can anyone confirm this? The 9 volt test scares me, whether it should or not. Thanks!

Rex Mills
05-13-2003, 07:07 PM
I believe you are correct on the polarity, cone should move forwaed with a positive signal at the black terminal. If the 9 volts scares you, try any 1.5 volt battery, such as AA or AAA.

boputnam
05-14-2003, 08:29 AM
The 9-volt test won't damage the L100's. It is indeed a brute-force level of test, but the large transducers (123A woofer) can handle this, and it won't get through the crossover.


I am fairly confident the L100 cabinet is positive. But, you can run the test easily enough. It is important, however, that you test the cabinet through the binding posts. The wiring to/from the crossover can reverse the action of the transducers. If the battery posts don't align for a simple connection directly to the speaker posts, grab a small length of lamp cord to shunt the two posts (+ to red).

The 123A is positive (cone excursion out on positive signal) which is quite anomalous for it's vintage. It may be JBL designed this transducer positive for its pedestrian use. The similar vintage 4312 is cross-wired so that the 2213H woofer (which is negative) runs positive.

email with questions.

4313B
05-14-2003, 09:17 AM
Here's a little cheat sheet for the L100/4310

boputnam
05-14-2003, 09:49 AM
Giskard...

You have a simply stunning and vast wealth of JBL knowledge. Incredible. I have JBL Envy!

I picture you surrounded by exotic transducers, jars of Aquaplas and long-lost mass rings, woofer brackets and compression drivers, walls lined with ring binders stuffed with network schematics and T-S parameters.

Wow.

Here's me:



Ha! (I hope that's nobody on this thread!)

boputnam
05-14-2003, 09:58 AM
But a bit more seriously...

That cheat-sheet is real interesting. Do you have (in that vast resource of JBL-ness of yours) schematics for the C533, L100, L100A, and 4310? Or Links to same?

Thanks.

4313B
05-14-2003, 10:13 AM
Yeah, I have schematics, but I've never gotten around to scanning them into a computer. The schematics are on the cheat sheet anyway, 13.5 uF S = 13.5 uF in series, 1.0 mH P = 1.0 mH in parallel, so you can sketch them up easy enough. :)

boputnam
05-14-2003, 10:37 AM
Yea, true enough. I was intested in seeing the signal path, because with the 123A being positive, the LF cone excursions as noted are not what I expected.

Thanks, as always.

4313B
05-14-2003, 11:08 AM
So, if you pull the LE10H out of the 4313 and put the positive terminal of a 1.5V or 9V battery to the LE10H's red terminal you get inward cone motion and if you do the same thing with your 123A you get outward cone motion? Which 123A do you have? -1? -3? or is it a 2212? What model loudspeaker is this out of?

boputnam
05-14-2003, 11:58 AM
LE10H moves in.
123A-1 moves out.
As I posted here, 18 April.
http://www.audioheritage.org/vbulletin/showthread.php?s=&threadid=9

It is not a 2212.

The 123A-1 was from an L100 (not mine...)

4313B
05-14-2003, 12:38 PM
Well that's goofy then, fortunately the 2212 is the only cone kit available for the 123A-1 so as those drivers are reconed they will be corrected. The schematics are based on the fact that all JBL transducers exhibited forward cone motion when positive voltage was applied to the black terminal.

Fortunately the L100/4310 sounds so terrible I'm quite sure whichever way you wire the LF will have no bearing on sound quality unless you're thinking "lesser of two evils".

ROFLOL, OMG I crack myself up! :p :p :p

According to recent events on ebay, if I hadn't tossed those four pair I ran across a few years ago into the trash I would be $4,000 ahead of the game :rolleyes:

boputnam
05-14-2003, 12:42 PM
I peed myself when I read that...!

Especially the line..."as those drivers are reconed they will be corrected."

Negative is good!!

;-p

Eaulive
08-18-2009, 03:14 PM
Here's a little cheat sheet for the L100/4310

Strange, I have 4 L-100 here, with four 123A-1, wired + to + and the cone does move out ... :blink:

According to your sheet the 123A-1 would be a negative driver... I have four of them here and they are positive.

Zilch
08-18-2009, 11:08 PM
Test the drivers themselves with a 1.5V battery.

Eaulive
08-19-2009, 11:09 AM
Test the drivers themselves with a 1.5V battery.

I did, trust me, forward cone motion with positive to the red terminal.
Inside the boxes the red connector goes to the red wire that goes to the green wire that goes to the red connector on the 123A

I have four of them, they're all wired this way :hmm:

boputnam
08-19-2009, 05:50 PM
According to your sheet the 123A-1 would be a negative driver... :no: You are mis-reading the info.


I have four of them here and they are positive.:yes: It is amongst a very few (2, to be exact) vintage woofers with positive cone motion.


Test the drivers themselves with a 1.5V battery.+1, er, +1.5!! :rotfl:


Inside the boxes the red connector goes to the red wire that goes to the green wire that goes to the red connector on the 123A

I have four of them, they're all wired this way :hmm:Perfect! That is the way JBL designed and built them. You are good to go!

btw, 1 MILLION points to "Eaulive" for doing extensive searches before posting! He resurrected a 2003 thread. Yeah - the system is cumbersome but it is working!

:applaud:

Eaulive
08-22-2009, 01:54 PM
btw, 1 MILLION points to "Eaulive" for doing extensive searches before posting! He resurrected a 2003 thread. Yeah - the system is cumbersome but it is working!

:applaud:

Maybe it's because I'm a moderator on another heavy traffic forum, so I know how irritating it may be when somebody opens a thread on a subject treated some days before :banghead:.

Eaulive
08-22-2009, 02:03 PM
:no: You are mis-reading the info.

Misreading no, misunderstanding maybe :D
According to the cheat sheet:
L-100 / 123A-1 / + to - / LF cones moves out.

Mine are wired + to + and LF cones moves out.
It's expected, but then I don't understand the cheat sheet :blink:

boputnam
08-22-2009, 07:01 PM
Mine are wired + to + and LF cones moves out.As it should do.

...but then I don't understand the cheat sheet :blink:OK. :)

Eaulive
08-23-2009, 06:29 AM
As it should do.
OK. :)

Care to explain? :)

boputnam
08-28-2009, 06:13 PM
Sorry - missed this.

The L100 had a number of variants, as you know. All were wired so the woofer moves out on (+) signal. This was a departure from predecessor cabinets. The 123A is unique.

If you mean the GRN is connected to the Red terminal, that is how it was designed and the cone will move out.

roadiemanchild
08-29-2009, 03:25 PM
My D130 also is a (-) for outward cone excursion. Or reversed polarity. Ya gotta check those or you find yourself doing it again and properly the second time.:applaud: